Indesit DSFE 1B10 Referenzhandbuch Seite 7

TROUBLESHOOTING
In case your dishwasher doesn't work properly, check if the problem can be solved by going through the following list.
For other errors or issues please contact authorized After-sales Service which contact details can be found in the warranty booklet.
Spare parts will be available for a period of either up to 7 or up to 10 years, according to the specific Regulation requirements.
PROBLEMS POSSIBLE CAUSES
The appliance has not been plugged in properly.
Power outage.
The dishwasher
won't start or does The dishwasher door is not closed.
not respond to
Cycle is interupted by door opening for > 4 sec.
commands.
It does not respond to commands.
The wash cycle has not finished yet.
The drain hose is bent.
The dishwasher
won't drain.
The sink drain pipe is blocked.
The filter is clogged up with food residues.
The dishes are rattling against each other.
The dishwasher
makes excessive
An excessive amount of foam has been produced.
noise.
The crockery has not been arranged properly.
The spray arms cannot rotate freely, being hindered
by the dishes.
The wash cycle is too gentle.
The dishes are not
An excessive amount of foam has been produced.
clean.
The cap on the rinse aid compartment has not been
shut correctly.
The filter is soiled or clogged.
There is no salt.
No water in the water supply or the tap is closed.
The dishwasher
does not fill the
The inlet hose is bent.
water.
All LEDs are
The sieve in the water inlet hose is clogged; it is
blinking rapidly.
necessary to clean it.
Drain hose positioned too low or siphoning into
Dishwasher finishes
home sewage system.
the cycle prema-
turely.
Air in water supply.
Policies, standard documentation, ordering of spare parts and additional product
information can be found by:
• Visiting our website docs.indesit.eu and parts-selfservice.whirlpool.com
• Using QR Code
• Alternatively, contact our After-sales Service (See phone number in the warranty booklet).
When contacting our After-sales Service, please state the codes provided on your product's
identification plate.
The model information can be retrieved using the QR-Code reported in the energy label.
The label also includes the model identifier that can be used to consult the portal of the registry at
https://eprel.ec.europa.eu .
SOLUTIONS
Insert the plug into the socket.
For safety reasons, dishwasher will not restart automatically when power returns.
Press the START/Pause button to resume the cycle.
Vigorously push the door until you hear the "click".
Close the door and press the START/Pause button.
Switch off the appliance by pressing the ON/OFF button, switch it back on after
approximately one minute and restart the program. If problem persists, unplug the
appliance for 1 minute, then plug it back in.
Wait until the wash cycle finishes.
Check that the drain hose is not bent (see INSTALATION INSTRUCTION).
Clean the sink drain pipe.
Clean the filter (see CLEANING THE FILTER ASSEMBLY).
Position the crockery correctly (see LOADING THE RACKS).
The detergent has not been measured out correctly or it is not suitable for use
in dishwashers (see FILLING THE DETERGENT DISPENSER). Restart dishwasher by
pressing the DRAIN button (see OPTIONS AND FUNCTIONS) and run new program
without detergent.
Arrange the crockery correctly (see LOADING THE RACKS).
Arrange the crockery correctly (see LOADING THE RACKS).
Select an appropriate wash cycle (see PROGRAMS TABLE).
The detergent has not been measured out correctly or it is not suitable for use in
dishwashers (see FILLING THE DETERGENT DISPENSER).
Make sure the cap of the rinse aid dispenser is closed.
Clean the filter assembly (see CARE AND MAINTENANCE).
Fill the salt reservoir (see FILLING THE SALT RESERVOIR).
Make sure there is water in the water supply or the tap running.
Make sure the inlet hose is not bent (see INSTALLATION) reprogram the dishwasher
and reboot.
After having carried out the verification and cleaning, turn off and turn on the
dishwasher and restart a new program.
Check if end of drain hose is placed at correct height (see INSTALLATION).Check for
siphoning into home sewage system, install air admittance valve if necessary.
Check water supply for leaks or other issues letting air inside.
EN
IEC 436
:
7