Werbung
Verfügbare Sprachen
Verfügbare Sprachen
BRAKING SYSTEM
The run-on brake engages when the trigger is released, causing the
tool to stop within seconds.
Make sure that the insertion tool comes to a complete stop before
laying it down.
In comparison with tools without a run-on brake the run-on time
will be highly reduced by braking.
If the time between releasing the switch and the stop of the
insertion tool increases to much, please have the tool serviced by
an authorized MILWAUKEE service facility.
SOFT START
Electronic soft start for save use prevents jerky run-up of the
machine.
MAINTENANCE
Remove the battery pack before starting any work on the appliance.
The ventilation slots of the machine must be kept clear at all times.
Use only Milwaukee accessories and Milwaukee spare parts. Should
components need to be replaced which have not been described, please
contact one of our Milwaukee service agents (see our list of guarantee/
GB
service addresses).
If needed, an exploded view of the tool can be ordered. Please state the
Article No. as well as the machine type printed on the label and order the
drawing at your local service agents or directly at:Techtronic Industries
GmbH, Max-Eyth-Straße 10, 71364 Winnenden, Germany.
EC DECLARATION OF CONFORMITY
We declare under our sole responsibility that the product described under
"Technical Data" ful lls all the relevant provisions of the directives
2011/65/EU (RoHS)
2006/42/EC
2014/30/EU
and the following harmonized standards have been used.
EN 60745-1:2009+A11:2010
EN 60745-2-3:2011+A2:2013
EN 55014-1:2017+A11:2020
EN 55014-2:2015
EN IEC 63000:2018
Winnenden, 2020-11-23
Alexander Krug / Managing Director
Authorized to compile the technical le
Techtronic Industries GmbH
Max-Eyth-Straße 10, 71364 Winnenden, Germany
GB DECLARATION OF CONFORMITY
We declare as the manufacturer under our sole responsibility that
the product described under „Technical Data" ful lls all the relevant
provisions of the following Regulations S.I. 2012/3032 (as amen-
ded), S.I. 2008/1597 (as amended), S.I. 2016/1091 (as amended)
and that the following designated standards have been used:
BS EN 60745-1:2009+A11:2010
BS EN 60745-2-3:2011+A13:2015
BS EN 55014-1:2017+A11:2020
BS EN 55014-2:2015
BS EN IEC 63000:2018
English
20
Winnenden, 2020-11-23
Alexander Krug / Managing Director
Authorized to compile the technical le
Techtronic Industries GmbH
Max-Eyth-Straße 10, 71364 Winnenden, Germany
SYMBOLS
CAUTION! WARNING! DANGER!
Please read the instructions carefully before starting the
machine.
Always wear goggles when using the machine.
Wear gloves!
Remove the battery pack before starting any work on the
appliance.
ANTI Vibration System
Braking System
Do not use force.
Only for cutting work.
Only for grinding.
Don't press the spindle lock button during start and
during running o .
Accessory - Not included in standard equipment, availa-
ble as an accessory.
Spare Part - Not included in standard equipment,
available as a spare part.
Do not dispose electric tools, batteries/rechargeable
batteries together with household waste material.
Electric tools and batteries that have reached the end of
their life must be collected separately and returned to an
environmentally compatible recycling facility. Check with
your local authority or retailer for recycling advice and
collection point.
n
Rated speed
V
Voltage
Direct Current
European Conformity Mark
British Conformity Mark
Ukraine Conformity Mark
EurAsian Conformity Mark
Werbung
