Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Operation
Call from external station.
When a call is made from the external station,
the videointercom turns on, generates an
acoustic tone and stays on for about 30
seconds. If the call time has expired and the
videointercom has turned off, press the button
"
" to reconnect with the calling external
station. Pick up the handset to start
conversation with the external station for about
90 seconds and press button "
the door.
In case of a call to a user with more than one
videointercom in parallel installed in the
apartment, all the videointercom will ring, but
only the videointercom with internal address
000 will turn on. You can answer from this
videointercom by following the instructions
above. You can answer from the other
videointercom by picking up the handset. This
operation will automatically turn ON this
videointercom and will turn OFF the intercom
that had been turned ON before. Press button
"
" if you want to see the caller before
answering and then pick up the handset.
Monitor function and connection with
one or more external stations.
With the system in stand-by and no
conversation in progress, it would be possible
to monitor the external door stations by picking
up the handset and pressing on the
videointercom the button
buttons previously programmed for this
function.
If the installation includes more external
stations and button "
" is programmed
correctly, you can monitor the external stations
(max. 4) in sequence by pressing the same
button again and again.
The videointercom will be turned ON for about
30 seconds. The monitoring will be interrupted
in case of request of monitor service by another
user, call between users or from an external
station.
If you pick up the handset during the monitoring,
you will automatically establish a voice
conversation with the external station.
If the videointercom will not turned ON when
you press button "
", this means the
installation is busy and you will have to wait
until it becomes free again.
Making or receiving a call from another
user.
When the installation is in stand-by, you can
make a call to another user. You must have
stored the address of the desired user's in the
numerical buttons. To make the call, pick up
the handset, wait for the free tone and press
button. You will hear the call tone and the
videointercom of the called user will ring
(without turning on) with a ring different from
calls from external stations or intercom calls
from the same apartment. If the called user
answers within 30 seconds, a 90-second
conversation starts, otherwise the system
goes back to free.
The internal conversation in progress will be
automatically interrupted in case of call from
external station to any other user.
If you pick up the handset and receive no tone,
the installation is busy and you must wait until
it is free.
Making or receiving an intercom call in your
apartment.
When the system is in stand-by it would be possible
to make a local intercommunicating call to all the
videointercoms installed in the apartment (max 6
monitors with internal address from 000 to 005) by
pressing buttons previously programmed with code
000.
To make the intercom call, pick up the handset, wait
" to open
for the free tone and press proper button. After
pressing the button you will get a calling tone on the
loudspeaker, while the videointercom of the called
user rings (without switching-ON) with the
programmed melody.
If the called user answers within 30 seconds, a 90-
second conversation starts, otherwise the system
goes back to free.
The internal conversation in progress will be
automatically interrupted in case of call from external
station to any other user.
Table 3. Button use for intercom calls of max. 6
videointercoms in the same apartment.
Calling video-
intercoms
VC0
(000)
VC1
(001)
VC2
(002)
or the other
VC3
(003)
VC4
(004)
VC5
(005)
N.B.: The codes in parenthesis in the table are the
identification addresses of the internal stations that
were programmed previously (see chapter
"programming of the user address and internal
address").
Examples:
- From videointercom VC1 (internal address 001)
press the button 1 for calls to videointercom VC0.
- From videointercom VC2 (internal address 002)
press the button 4 for calls to videointercom VC4.
- From videointercom VC4 (internal address 004)
press the button 4 for calls to videointercom VC3.
Adjusting brightness and contrast (or colour)
Videointercom to call
VC0 VC1 VC2 VC3 VC4 VC5
-
-
-
-
-
-
Button to press
(all programmed with code 000)
Tone table
Tone of pressure of a button.
indicate the pressure of the buttons.
Monitor function.
Activated on monitor function
and confirmation of programming value
Tone.
You must pick up the handset to enter the
programming mode
Activation.
Activated on button
numerical buttons if programmed with actuator
address
Programming.
It confirms the beginning of the
programming mode
Acknowledge tone.
It is activated during the
programming phase to indicate a valid operation.
Tone of system ready.
Activated for 30 seconds
if the system is free
0
1
2
3
Calling tone.
It is activated during a call to another
user or during an intercommunicating call (active
for 30 seconds or until the called user answers).
0
1
2
3
Busy.
Activated on button pressure with busy line
0
1
2
3
Dissuasion tone.
It is activated when a non-
existent device is call or when a device is not
available
0
1
2
3
End conversation tone.
It is activated 10 seconds
before the conversation time ends
0
1
2
3
Note. All the acoustic signalling, with the exception
of the system ready and calling tone, last after
about 2 seconds.
Calling table
1
DIN-DON
9
2
DRING1
10 MELODY5
3
DRING2
11 MELODY6
4
DRING3
12 MELODY7
5
DRING4
13 MELODY8
6
MELODY1
14 BEEP
7
MELODY2
8
MELODY3
It is activated to
pressure and
4
5
4
5
4
5
4
5
4
5
MELODY4
Mi 2400
- 9 -
Werbung
