Werbung
Verfügbare Sprachen
Verfügbare Sprachen
System programming
The following programming allows you to
personalise the operation mode of button "1"
used to deactivate the ring tones and the GC-GE
terminals and send the floor call to the systems
with the same user address (internal stations in
parallel). See table 2.
To make the programming it is necessary:
enter the programming mode following the
instructions described in "Enter the
programming mode";
keep pressed the button "
seconds; yellow LED starts flashing;
a - keep pressed the button "
4 seconds; yellow LED starts quickly flashing;
b - press the button "1" once to enable operating
mode 0 (you hear a sharp tone); within 2
seconds press the button "1" again to disable
operating mode 0 (you hear a low tone);
c - press the button "
" to confirm and go on
to program the next mode;
you must repeat steps a, b and c to program all
operating modes in table 2;
after you have completed the operation and
confirmed operating mode 7 with the button
"
", press the button "
" and replace the
handset to exit the programming phase.
Note. Programming will not be changed if the
values of all modes are not entered correctly.
- Programming example of page 8.
Table 2 - System programming codes
Operating modes
mode 0
send floor call to other internal stations in parallel (1)
mode 1
button "1" deactivates all ring tones (2)
mode 2
button "1" deactivates all ring tones and button tones (2)
mode 3
button "1" does not deactivate ring tones and button tones (2)
mode 4
reserved; disabled
mode 5
the GC-GE terminals are activated upon call from external door station (3) disabled
mode 6
the GC-GE terminals are activated upon intercom call (3)
mode 7
door open warning
(1) From the internal station connected to the floor call button (terminal A1) and with operating mode 0 enabled, the floor call is also sent to the other
apparatuses in parallel.
(2) If modes 1, 2 and 3 are disabled, press the button "1" for 4 seconds , without a conversation in progress, to deactivate the external
and intercommunication ring tones. To reactivate the ring tones, press the button "1" again for 4 seconds; you hear the confirmation
tone.
(3) If modes 5 and 6 are disabled, the GC and GE terminals are activated to send the calls.
Example of system programming to enable operating mode 0 and 2 and to disable all the others operating modes
Resetting the default programming values
To reset the videointercom default programming
values and delete all the variations made in the
programming mode you must:
enter the programming mode following the
instructions described in "Enter the program-
ming mode";
press the buttons 5, 4, 3, 2 and 1 successively;
the tone indicates that the default values have
been restored.
" for more than 4
" for more than
Additional functions
Call floor
To have the floor call connect the apparatus as
illustrated in the diagram.
Call Repeat
You can connect the apparatuses as illustrated in
the diagram below to sent the videointercom ring
to other locations in the house.
WB3262
GC
GE
230V
127V
0
PRS210
Deactivate/activate ring tones
By default, press the button "1" for 4 seconds ,
without a conversation in progress, to deactivate
the external and intercommunication ring tones.
To reactivate the ring tones, press the button "1"
again for 4 seconds; you hear the confirmation
tone.
Default
To enable
value
press 1 time
button "1"
disabled
enabled
disabled
enabled
disabled
enabled
disabled
enabled
disabled
-
enabled
disabled
enabled
disabled
enabled
9T
6
7
5
1
1471E
max 50V-5A
To disable
press 2 times
button "1"
disabled
disabled
disabled
disabled
disabled
disabled
disabled
disabled
Mi 2400
- 8 -
Werbung
