Werbung
Verfügbare Sprachen
Verfügbare Sprachen
PROGRAMMING
The videointercom must be suitably programmed
for operation.
Two programming modes are available:
-automatic (quick programming of user code
acting from external station);
-manual (programming of all videointercom
functions)
The following programming is possible:
- user address;
- internal address;
- address to assign to button " "; maximum
4 addresses of external door stations;
- code to assign to buttons "1", "2", "3", "4",
and "5" to make intercom calls, door station
monitoring or for special services;
- selection of the call timing and call melody
for 4 different call melodies (see table 1).
Factory setting
- user address
= 100
- internal address = 000
- buttons " ", "1", "2", "3", "4", "5" = no codes
are stored to the buttons
- number of call rings and call melody (see
table 1)
Table 1.
Factory setting for calls
Number Type of
Calls
of rings
from door station
1
intercommunicating
4
from other users
4
floor (local)
1
Attention: it is mandatory to program the
equipment only with the user code (address) all
other programming are optional.
Enter the programming mode
Hold the button
pressed for more than 4
seconds and pick up the handset after the
confirmation tone; the yellow LED turns on and
stays on for the entire programming selection
phase.
Release the button
.
If for 2 minutes no keys are pressed, system
switches back to the operating mode.
Exit the programming phase
You can exit the programming mode at any time
by replacing the handset; yellow LED turns-OFF.
Automatic programming
You can use the automatic programming mode
to save the videointercom address from the
external station. To enter the automatic
programming mode you must:
enter the programming mode following the
instructions described in "Enter the
programming mode";
make a call from an external station within
2 minutes. In case of installations with digital
push-button keyboard TD2100, key in the
number you want to assign to the videointercom
and press "
". In case of installations with
digital encoder CD2131÷CD2138 press the
button you want to assign to the user on the
push-button keyboard. When the call is
received, the videointercom is programmed
automatically, you hear the call tone in the
loudspeaker and the videointercom is turned
on, showing the calling external station. Close
and pick up the handset to start a conversation
with the external door station and verify the
correct working mode of the equipment;
programming mode is signalled on the external
door station by an acknowledge tone if
accepted or a dissuasion tone if rejected;
repeat programming phases for all the
videointercoms connected to the system.
Manual programming
The manual programming mode allows you to
enter the user address, assign the internal address
and codes to buttons from 1 to 5 and " "
(example of programming to page 14).
Using the push-buttons for programming
Press button "
addresses or codes.
: Press this button to confirm address or
code programming or go to the next
programming step.
: Press this button to confirm the digit just
dialled and to proceed to enter next digit in
the following order: hundreds, tens, units.
1 : Press this button to increase the value
you want to enter. Press the button for a
number of times equal to the digit you want
to enter (digit 1 = 1 time; digit 9 = 9 times;
melody
digit 0 = 10 times).
Din-Don
Entering codes or addresses
Dring 1
- Codes and/or addresses must have three digits
Dring 2
(hundreds, tens, units); codes and/or addresses
with tens and units or units only must be
Dring 3
completed by adding zeros. For example,
address 96 will become 096 and address 5 will
become 005.
- Digits must be entered individually (beginning
from the hundred), by pressing the button "1" for
a number of times "n", where "n" is the value of
the digit you want to enter. Store the digit pressing
the button " "; a tone will confirm the acquisition
of the 1
digit.
st
- Follow the same procedure to store the 2nd
and 3rd digit.
For example, to enter code 096 you must:
- press button "1" 10 times to enter digit 0 and
press the button " "; you will get a tone on the
loudspeaker;
- press button "1" 9 times to enter digit 9 and
press the button " "; you will get a tone on the
loudspeaker;
- press button "1" 6 times to enter digit 6 and
press the button " "; you will get a tone on the
loudspeaker.
Programming of the user address and
internal address
- User address – this code allows you to receive
an external call, turn on the videointercom, have
a conversation and open the door at the calling
external station.
- Internal address – these codes are used to
identify the videointercoms installed in the
apartment (max.6). In case of one videointer-
com only, the internal code must be 000 (default
value); if other videointercoms are present (max.
other 6) you must assign to them the codes 001,
To program the user address and internal
address it is necessary to:
", " " and "1" to enter
Note. If one of the two above mentioned
addresses is already correctly programmed and
you don't want to program it again it would be
possible to skip its programming by simply
pressing button
Programming address to be stored to each
button
Button " ". To this button can be stored the
addresses of maximum 4 external stations which
can be connected sequentially. In this way the
user can monitor, communicate or open the door
of 4 different external stations without being called
from them but simply pressing several times the
button
external door station it isn't necessary to
store any address because it will be acquired
automatically at the first call.
To make the programming it necessary to:
002, 003 etc. Programming these addresses
all the videointercoms will ring-UP when
receiving an external, intercommunicating or
floor (local) call (if programmed).
enter the programming mode following the
instructions described in "Enter the
programming mode";
keep pressed the button
for more than 4
seconds; yellow LED starts flashing;
enter the 3 digit of the user address following
the procedure reported on the paragraph
"Entering codes or addresses";
press the button
to confirm the present
phase and move to the next phase which is:
programming of the internal address; an
acknowledge tone will be heard;
enter the 3 digit of the internal address
following the procedure reported on the
paragraph "Entering codes or addresses";
press the button
to confirm; an acknowl-
edge tone will be heard and the yellow LED
lights-ON continuously;
proceed with another programming phase or
exit the programming mode by hanging up the
handset.
.
. In the case of a system with only 1
enter the programming mode following the
instructions described in "Enter the
programming mode";
keep pressed the button " " for more than 4
seconds; yellow LED starts flashing;
enter the 3 digit of the address of the 1st
external door station to be stored (codes
from 231 to 250) following the procedure
reported on the paragraph "Entering codes
or addresses";
press the button
to confirm the present
address move to the 2nd one; an acknowledge
tone will be heard;
enter the 3 digit of the address of the 2nd
external door station and confirm by pressing
button
;
proceed entering the addresses of the 3rd and
4th external stations (if present) or exit the
present programming phase pressing several
times the button
, you will be led back to
selecting programming mode;
proceed with another programming or exit the
programming mode by hanging up the hand-
set.
Mi 2400
- 6 -
Werbung
