HIKMICRO HM-TD5567T-15/W Schnellstartanleitung Seite 9

IN THE EVENT OF ANY CONFLICTS BETWEEN THIS
MANUAL AND THE APPLICABLE LAW, THE LATTER
PREVAILS.
Regulatory Information
These clauses apply only to the products bearing
the corresponding mark or information.
FCC Information
Note: This equipment has been tested and found
to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference when the
equipment is operated in a commercial
environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not
installed and used in accordance with the
instruction manual, may cause harmful
interference to radio communications. Operation
of this equipment in a residential area is likely to
cause harmful interference in which case the user
will be required to correct the interference at his
own expense.
Please take attention that changes or modification
not expressly approved by the party responsible
for compliance could void the user's authority to
operate the equipment.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two
conditions:
(1) This device may not cause harmful
interference, and
(2) This device must accept any interference
received, including interference that may cause
undesired operation.
EU Conformity Statement
This product and - if applicable - the
supplied accessories too are marked with
"CE" and comply therefore with the
applicable harmonized European standards listed
under the Directive 2014/30/EU(EMCD), Directive
2001/95/EC(GPSD) and Directive 2011/65/EU(RoHS).
Directive 2012/19/EU (WEEE Directive):
Products marked with this symbol cannot
be disposed of as unsorted municipal
waste in the European Union. For proper
recycling, return this product to your local supplier
upon the purchase of equivalent new equipment,
or dispose of it at designated collection points. For
more information see: www.recyclethis.info
Directive 2006/66/EC and its amendment
2013/56/EU (Battery Directive): This
product contains a battery that cannot be
disposed of as unsorted municipal waste in
the European Union. See the product
documentation for specific battery information.
The battery is marked with this symbol, which may
include lettering to indicate cadmium (Cd), lead
(Pb), or mercury (Hg). For proper recycling, return
the battery to your supplier or to a designated
collection point. For more information see:
www.recyclethis.info.
Industry Canada ICES-003 Compliance
This device meets the CAN ICES-3 (A)/NMB-3(A)
standards requirements.
KC
A 급 기기: 이 기기는 업무용(A 급)
전자파적합기기로써 판매자 또는 사용자는 이 점을
주의하시기바라며, 가정 외의 지역에서 사용하는
것을 목적으로 합니다.
RCM
Warning: This is a class A product. In a domestic
environment this product may cause radio
interference in which case the user may be
required to take adequate measures.
Safety Instructions
These instructions are intended to ensure that
user can use the product correctly to avoid danger
or property loss.
Laws and Regulations
The device should be used in compliance with
local laws, electrical safety regulations, and fire
prevention regulations.
Transportation
Keep the device in original or similar packaging

while transporting it.
Keep all wrappers after unpacking them for

future use. In case of any failure occurred, you
need to return the device to the factory with the
original wrapper.
Transportation without the original wrapper may

result in damage on the device and the company
shall not take any responsibilities.
Do not drop the product or subject it to physical

shock. Keep the device away from magnetic
interface.
Power Supply
Input voltage should meet the Limited Power

Source (24 VDC) according to the IEC62368
standard. Please refer to technical specifications
for detailed information.
Make sure the plug is properly connected to the

power socket.
The socket-outlet shall be installed near the

equipment and shall be easily accessible.
DO NOT connect multiple devices to one power

adapter, to avoid over-heating or fire hazards
caused by overload.
DO NOT touch the bare metal contacts of the

inlets after the circuit breaker is turned off.
Electricity still exists.
+ identifies the positive terminal(s) of equipment

which is used with, or generates direct current. -
identifies the negative terminal(s) of equipment
which is used with, or generates direct current.
Ensure correct wiring of the terminals for

connection to an AC mains supply.
Use the power adapter provided by qualified

manufacturer. Refer to the product specification
for detailed power requirements.
Battery
6