Grundig GV 500 SV/1 Serviceanleitung Seite 14

The GRUNDIG user guide on the
screen of the TV set
... offers a dialogue between you and the recorder.
The recorder responds to many functions which
you select using the remote control, with info tables
and dialogue lines on the screen of the TV set.
Button symbols for the remote control and dialogue
lines indicate the next operating step, and options.
You are guided step by step, simply and understan-
dably.
Calling up the info table
Press the h button on the remote control.
1
PROG. DAY START STOP
ON/OFF
1 2 3
5
4 6
7 8 9
0
VPT AV
PROG DAT
> RTL2
ARD
PRO7 03ED
ZDF
VOX
I SW3
– – – – – – – – – – – – – – – – – – – – – – –
Button on the Representation in Function
remote control the info table and
the dialogue lines
h
i
Calls up the info table and switches back to the TV picture.
1 2 ... 9 0 0–9
For entering data directly.
DC
For step by step selection of functions or lines in a table.
F E
For switching between tables, for selecting data, and for altering settings.
B
+ –
For entering data step by step for TIMER recording.
G
OK
For activating a function and for confirming data and settings.
¢
CLEAR
For deleting data.
CLEAR
¢
none To end info tables and settings at any time .
6
Preparation
1 Switch the TV set on.
2 Select the programme position for the video recor-
der at the TV set (AV programme position).
!
If the recorder is connected to a TV set with Mega-
logic functions, the procedure is carried out auto-
matically. When you press the h button the TV set
is switched on and the AV programme position is
selected automatically.
INFO table
Record Programming
A2 Record Prepared
Child lock
Info Duration
Installation
Set Time/Date
– – – – – – – – – – – – – – – –
OK i
START STOP
01 12:01 13:00 *
02EW 10:01 11:00 *
08:00 09:00
04 00:00 00:10
05 00:20 00:30
06 01:40 02:12
Dialogzeilen
Dialogue lines
CLEAR OK i
Setting the time and date
! The digital clock continues to operate (for up to 7
days) after the recorder has been disconnected
from the mains supply. However, the time is not
displayed and the yellow indicator on the recorder
is off.
!
If necessary, set the language for the user guide.
Follow the instructions in the chapter "Selecting the
language for the user guide" on page 26.
Preparation
Switch the TV set on.
1
Select the AV programme position for the video
2
recorder at the TV set (serves as monitor).
Operation
Call up the info table using the h button.
1
Use the DC buttons to select the » Set Time/Date «
2
line and call it up using the G button.
– The » Set Time/Date « table appears.
Time: 20:15
Date: 19.08.94
– – – – – – – – – – – – – – – – – – –
0-9 OK i
Enter the time as a four-digit number using the
3
numbered buttons 1 ... 0.
Use the D button to select the » Date « line and
4
enter the date as a six-digit number using the num-
bered buttons 1 ... 0.
Confirm the entry using the G button.
5
¢
End the setting using the button.
6
8
Tuning TV stations
Television stations broadcast programmes on diffe-
rent frequencies/channels.
The recorder has a built-in receiver. It can thus
receive and record television programmes indepen-
dently of the TV set.
First, you must tune your recorder to the channels
used by the different TV stations.
99 programme positions are available. They can be
occupied as required with TV stations from the aeri-
al or a cable connection.
A number of options are available for tuning:
1. By transfer of data from the TV set.
The TV set must be provided with Megalogic fun-
ctions.
2. With the automatic tuning system (ATS euro
plus). The recorder searches, sorts, and stores
all channels/special channels which can be recei-
ved at its location.
This procedure depends on the language and
country you select, as well as the quality of
reception of the TV stations.
If you are not satisfied with the order in which
the TV stations are allocated, the order can be
changed later.
3. By entering data directly.
4. By searching manually, for example if there are
new TV stations, or if the recorder cannot find a
TV station with the automatic tuning system.
Accepting data from the TV set
(Megalogic function)
If the recorder is connected to a TV set with Mega-
logic function, the recorder automatically accepts
the TV programmes that are stored in the TV set.
To enable the recorder to this, you must carry out
the following steps in the order indicated.
!
Recorder and TV set must be connected with the
EURO-AV cable provided with your recorder, and
the TV set must be switched on.
1 Remove the plug for the recorder from the mains.
2 Re-insert the plug for the recorder into the mains.
– The recorder automatically accepts the TV
programmes from the TV set.
Thus the recorder will have the same programme
position assignments as the TV set.