IKRA Mogatec BVN 2500 Gebrauchsanweisung Seite 19

Preparing of the blower vac prior to use
The blower vacuum requires some assembly prior to use
for the first time This includes the fitting of the blow/vac
tube to the housing and the fitting of the collection bag.
Handle assembly
(Fig. 1-2)
Support handle attached as shown on the images to
push up in the housing and plug it firmly into place.
Assemble the Tube and wheel bracket
1. Insert the lower tube to the upper tube and align the
screw hole in the upper tube with the screw hole in
the lower tube, at the same time the convex plate can
match the slot on upper tube firmly (fig. 3).
2. Locate one screw (A) (ST4.2x50) in big screw hole on
upper tube (fig. 5).
3. Tighten the screw securely and torque to 1.2 Nm mini-
mum.
4. Assemble the Wheel Bracket: Insert the wheel bracket
from the end Lower tube till it reach the rib position
and can not forward again (fig. 6).
5. Locate one screw (ST4.2x15) in the screw hole on
wheel bracket (fig. 7).
6. Tighten the screw firmly (fig. 8).
7. The ready-mounted suction - and blowpipe with strong
pressure to stop the import motor housing. (Fig. 8 a).
The tube with the supplied screw (ST 4.2 x 50) firmly
connected (Fig. 8 b)
Fitting the collection bag
1. Connect the strap(15) onto the hook (4) in the housing
(fig. 9)
2. Attach the push-on collection bag connector (8) to the
outlet tube of the housing. Push the fitting of the col-
lection bag directly onto the outlet until it "clicks" into
position (fig. 10).
3. Repeat the first step to connect the strip to the second
hook on the underside of the housing.(Fig. 11)
4. To remove the collection bag, disconnect the attach-
ments in the reserve order.
5. When removing the fitting on the outlet, first depress
the two buttons on either side of the plastic connector
(fig. 10), and then pull.
ATTACHING THE SHOULDER HARNESS
1. Connect the latch (14) on the shoulder harness (1) to
the strap hanger in main housing.
2. Adjust the strap to a comfortable position.
Operation of the blower vac
Prior to using the blower vac, ensure you have read and
understood this instruction manual.
• Ensure you are wearing suitable clothing and also
safety equipment like safety glasses, ear protection
and s mask of necessary.
• Ensure the attachments to the blower vac are correctly
fitted and adjusted.
• Be aware of other people and animals in the area
where you are to be operating the blower vac.
(fig. 3-8)
(fig. 9-11)
(Fig.12)
To turn the blower vac on.
1. Plug the power cord into an approved electrical exten-
sion cord, and turn the extension cord on. Attach the
extension to one side of the cable hook as shown in
fig. 16.
2. Ensuring the blower vac is directed in a safe direction,
depress the trigger switch (2) and the blower vac will
start.(fig 12)
Be sure to be holding the blower vac firmly on start up.
To turn the blower vac off
To turn the blower vac "off", simply release the trigger
switch.
Important ! After you have turned the blower vac off, do
not leave the product until the electrical supply.
Select the blow operation
1. Move the blower/vacuum selector level (6) towards
the back of the housing (fig. 13)
When the blower operation is selected, air is drawn up
through the large blow/vac tube and then expelled at a
much higher velocity in the lower cavity below the blow/
vac tube.
Ensure when the blower operation is selected the blower
vac is pointed, directed and used in a safe manner. Do
not direct the air flow from this blower vac directly or
indirectly towards another person.
To select the vacuum operation
1. Push the selector level (6) forward (fig. 14).
When the vacuum operation is selected, air and debris is
drawn up through the large vac tube, and forced through
the mulching impellor.
The debris is mulched and then blown down into the
collection bag.
Important! Always ensure the collection bag is correctly
attached as per the "Fitting the collection bag " section
in this manual.
Always be aware of what is being drawn up into the
blow/vac tube. This product is only designed for garden
debris like leaves, twigs and garden cuttings.
Important notes when using the blower/vacu-
um selector knob (6)
Do not force the lever. The lever should move with very
little resistance. If the lever is difficult to move, discon-
nect the power supply ,remove the collection bag and
ensure debris, dirt or mud has not jammed the lever
inside the large round outlet.
When selecting either of the operation, ensure the selec-
tor lever is fully in one position of the other, not half way.
Speed Controller
Produkt BVN 2500 has a adjustable speed controller and
therefore adjustable vacuuming and blowing. The speed
is fully variable from 6000 Rpm to 14000 Rpm.
GB-5
(Fig.15)