Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
INSTALLATION INSTRUCTIONS
Maximum distances Driver - LED
Distance (m)
Cable section (mm²)
Driver constant voltage (150W - 24V / 70W - 12V)
Distance (m)
Cable section (mm²)
Distance (m)
Cable section (mm²)
Distance (m)
Cable section (mm²)
Distance (m)
Cable section (mm²)
Distance (m)
Cable section (mm²)
The AR330500TC device has been designed for piloting, powering and control of LED lighting equipment with RGB technology.
It uses a PWM (Pulse Width Modulation) technique to control the intensity of the three primary colours (Red, Green, Blue); by
means of the additive colour synthesis process it is theoretically possible to reproduce any colour.
PWM technology consists of LEDs turning on and off at speeds that are higher than the optical persistence in the retina (about
200 Hz). The perceived intensity is proportional to the ratio between the on and off times. The driver is equipped with outputs for
piloting current controlled LED equipments.
The connection is carried out with 6 wires (+R-R,+G-G, +B-B). The piloting current is 500 mA. The intensity of the primary colours
is controlled with 8 bit bytes corresponding to 256 levels; it is therefore possible to obtain by synthesis up to 16.7 million colours.
To carry out colour dynamic change sequences, the device has the following function modes.
The "stand-alone" mode, which offers the following options: with the "Easy-Run-Menu" function it allows a sequence (show) to be
chosen from those already stored in the memory of the device and to reproduce it with a desired selectable speed. The device
can be connected to a remote push button to manually activate execution of the selected sequence. It is possible to synchronize
other units without any control connection between the various devices. In this case synchronization is entrusted to the internal
quartzes and all the devices must be connected to a single power supply and the same show and the same running speed on
each device must be selected.
Thanks to the interface which is compatible with the USITT DMX 512(1990) protocol it is possible: to interlock the function of the
device to a control unit or an external DMX recorder, executing any program. Insert the product in a DMX configuration with chain
connections (daisy-chain), connecting other DMX devices through the in/out connectors.
DMX In:
Input DMX signal
DMX Out:
Output DMX signal
DIP 1:
DIP group with 12 dip-switch commutators
Red LED DATA:
LED DMX data monitoring and show speed
Green LED ON:
LED connection to mains 230Vac
R G B:
Direct current outputs for piloting current LEDs
LN:
Input power
PB:
Input external control push button
L&L Luce&Light srl / Via Trescalini, 5 / 36031 Dueville, Vicenza / Italy / T +39 0444 36 05 71 / F +39 0444 59 43 04
Driver constant voltage (max. 70W - 24V)
5
10
0,75
1
5
10
1,5
2,5
Driver constant current (350mA - 500mA)
5
10
0,25
0,25
Driver constant current (700mA - 1A)
5
10
0,5
0,5
Dimmable driver (350mA - 500mA)
5
10
0,25
0,25
Dimmable driver (700mA - 1A)
5
10
0,5
0,5
E lucelight@lucelight.it / www.lucelight.it
20
30
1,5
2,5
20
30
4
4
20
50
0,5
1
20
50
1
2,5
15
-
0,5
-
15
-
1
-
60
2,36''
36
1,42''
AR330500TC
Cable for connection to the network
Min 3x0.75 mm²
210
8,27''
225
8,86''
45
1,77''
3/8
Werbung
Inhaltsverzeichnis
