Maintenance And Service - Bosch UniversalCut 18V-65 Originalbetriebsanleitung

Seite von 195

/ 195
Inhalt
Inhaltsverzeichnis
Lesezeichen

Inhaltsverzeichnis

Verfügbare Sprachen

Selecting the saw blade

Only use saw blades that are suitable for the material you are going to cut. The saw blade should not be longer than required

for the cut you want to make.

Saw blade

NanoBlade Wood Basic

NanoBlade Wood Speed

Inserting the saw blade (see figure A)

Use only clean saw blades. Make sure that the saw

blade receptacle is free of chips and sawdust.

Use the locking lever (10) to open the cover (9) of the saw

blade receptacle. Insert the saw blade as shown in the fig-

ure. Make sure that the drive shaft and the end of the saw

blade fit in the recess on the saw blade receptacle (13).

Close the cover of the saw blade receptacle and lock it with

the locking lever. You should hear the locking lever click into

place.

The chain of the saw blade is tensioned automatically.

If the chain slips through or becomes detached from the

guide unit, open and close the cover (9) of the saw blade re-

ceptacle.

Removing the saw blade

Open the locking lever (10) fully open the cover (9) of the

saw blade receptacle. Remove the saw blade.

Dust/Chip Extraction

Dust from materials such as lead-containing coatings, some

wood types, minerals and metal can be harmful to one's

health. Touching or breathing-in the dust can cause allergic

reactions and/or lead to respiratory infections of the user or

bystanders.

Certain dust, such as oak or beech dust, is considered carci-

nogenic, especially in connection with wood-treatment ad-

ditives (chromate, wood preservative). Materials containing

asbestos may only be worked by specialists.

– Provide for good ventilation of the working place.

– It is recommended to wear a P2 filter-class respirator.

Observe the relevant regulations in your country for the ma-

terials to be worked.

Avoid dust accumulation at the workplace. Dust can

easily ignite.

Operation

Never bend the saw blade

Starting Operation

Switching on/off

To switch on the power tool, press the lock-off button (4) to

the left or right. Then press the on/off switch (5) and keep it

pressed.

Bosch Power Tools

Cutting depth

Order number

50 mm

2 609 256 D83

65 mm

2 609 256 F43

50 mm

2 609 256 D84

65 mm

2 609 256 D86

Once the power tool is switched on, you can release the lock-

off button (4).

To switch off the power tool, release the on/off switch (5).

Controlling the sawing speed

You can control the speed of the power tool when switched

on by how hard you press the on/off switch (5). The speed is

continuously variable.

The sawing speed required depends on the material and the

working conditions; it can be ascertained through practical

tests.

It is advisable to reduce the sawing speed when placing the

saw blade on the workpiece.

Temperature-dependent overload protection

In normal conditions of use, the power tool cannot be over-

loaded. If the power tool is overloaded or the permitted bat-

tery temperature is exceeded, the electronics of the power

tool will switch off until the temperature returns to within the

optimum operating temperature range.

Working Advice

Switch the power tool off immediately if the saw blade

becomes blocked.

Always use a sturdy support when working on small or

thin workpieces.

Make sure you always cut from front to back (see

figure B) or from top to bottom (see figure C) when

sawing.

To increase the cutting speed, saw in a gentle rocking motion

(in the cutting direction).

Switch the power tool off immediately if the saw blade jams.

Widen the sawing gap slightly with a suitable tool and pull

the power tool out.

The riving knife (3) prevents sawing against the running dir-

ection of the chain saw (see figure D).

Put the cover (12) on the saw blade (1) after finishing work

in order to protect it.