Technical Data; Cordless Impact Wrench - AEG BSS18HTF12B6-0 Originalbetriebsanleitung

TECHNICAL DATA

Production code......................................................................
Tool reception .........................................................................
No-load speed ........................................................................
Impact rate (high speed).........................................................
Max. torque.............................................................................
Nut busting torque ..................................................................
Max. diameter bolt / nut ..........................................................
Battery voltage........................................................................
Weight according EPTA-Procedure 01/2014 (1.5 Ah ... 9.0 Ah) ........
Recommended ambient operating temperature .....................
Recommended battery types..................................................
Recommended charger ..........................................................
Noise/vibration information
Measured values determined according to EN 62841.
Typically, the A-weighted noise levels of the tool are:
Sound pressure level (Uncertainty K=3dB(A)).....................
Sound power level (Uncertainty K=3dB(A)) .........................
Wear ear protectors!
Total vibration values (vector sum in the three axes)
determined according to EN 62841.
Vibration emission value a
h
Impact tightening of fasteners of the maximum capacity of the tool
Uncertainty K= .....................................................................
WARNING
The vibration and noise emission level given in this information sheet has been measured in accordance with a standardized
test given in EN 62841 and may be used to compare one tool with another. It may be used for a preliminary assessment of
exposure.
The declared vibration and noise emission level represents the main applications of the tool. However if the tool is used for
diff erent applications, with diff erent accessories or poorly maintained, the vibration and noise emission may diff er. This may
signifi cantly increase the exposure level over the total working period.
An estimation of the level of exposure to vibration and noise should also take into account the times when the tool is switched
off or when it is running but not actually doing the job. This may signifi cantly reduce the exposure level over the total working
period.
Identify additional safety measures to protect the operator from the eff ects of vibration and/or noise such as: maintain the tool
and the accessories, keep the hands warm, organization of work patterns.
WARNING Read all safety warnings, instructions,
illustrations and specifi cations provided with this power
tool. Failure to follow all instructions listed below may result
in electric shock, fi re and/or serious injury.
Save all warnings and instructions for future reference.
IMPACT WRENCH SAFETY WARNINGS
Hold the power tool by insulated gripping surfaces,
when performing an operation where the fastener may
contact hidden wiring. Fasteners contacting a „live" wire
may make exposed metal parts of the power tool „live" and
could give the operator an electric shock.
Wear ear protectors. Exposure to noise can cause hearing
loss.
ADDITIONAL SAFETY AND WORKING INSTRUCTIONS
Use protective equipment. Always wear safety glasses when
working with the machine. The use of protective clothing is
recommended, such as dust mask, protective gloves, sturdy
non-slip footwear, helmet and ear defenders.
The dust produced when using this tool may be harmful to
health. Do not inhale the dust. Wear a suitable dust
protection mask.
Do not machine any materials that present a danger to
health (e.g. asbestos).
Switch the device off immediately if the insertion tool stalls!
Do not switch the device on again while the insertion tool is
stalled, as doing so could trigger a sudden recoil with a high
reactive force. Determine why the insertion tool stalled and
rectify this, paying heed to the safety instructions.
The possible causes may be:
• it is tilted in the workpiece to be machined
• it has pierced through the material to be machined
16 ENGLISH
470 327 - BSS18HTF12B6_EN62841.indd 16 470 327 - BSS18HTF12B6_EN62841.indd 16

CORDLESS IMPACT WRENCH

Автотовары «130»
BSS18HTF12B6
.....................4771 66 01...
...000001-999999
.........................1/2" (12,7 mm)
-1
....................0-1800 min
-1
....................0-2300 min
.......................1550 Nm
.......................2100 Nm
........................M30
...........................18 V
........... 3,4 kg ... 4,1 kg
.................-18...+50 °C
................ L1815R, ... L1890R
.. AL18G, AL1218G, BL1218, BLK1218
........................95,0 dB (A)
......................106,0 dB (A)
2
........................13,7 m/s
2
..........................1,5 m/s
• the power tool is overloaded
Do not reach into the machine while it is running.
The insertion tool may become hot during use.
WARNING! Danger of burns
• when changing tools
• when setting the device down
Chips and splinters must not be removed while the machine
is running.
When working in walls ceiling, or fl oor, take care to avoid
electric cables and gas or waterpipes.
Clamp your workpiece with a clamping device. Unclamped
workpieces can cause severe injury and damage.
Remove the battery pack before starting any work on the
machine.
Do not dispose of used battery packs in the household
refuse or by burning them. AEG Distributors off er to retrieve
old batteries to protect our environment.
Do not store the battery pack together with metal objects
(short circuit risk).
Use only System GBS chargers for charging System GBS
battery packs. Do not use battery packs from other systems.
Never break open battery packs and chargers and store
only in dry rooms. Keep dry at all times.
Battery acid may leak from damaged batteries under
extreme load or extreme temperatures. In case of contact
with battery acid wash it off immediately with soap and
water. In case of eye contact rinse thoroughly for at least 10
minutes and immediately seek medical attention.
Warning! To reduce the risk of fi re, personal injury, and
product damage due to a short circuit, never immerse your
tool, battery pack or charger in fl uid or allow a fl uid to fl ow
inside them. Corrosive or conductive fl uids, such as
04.06.2020 12:16:05 04.06.2020 12:16:05