Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Changing the speed and temperature settings for
auxiliary functions
Depending on the step the programme has reached, you
may cancel or activate the auxiliary functions; see, "Auxiliary
function selection".
You may also change the speed and temperature settings;
see, "Spin speed selection" and "Temperature selection".
C
If no change is allowed, the relevant light will flash for
3 times.
4.15
Adding or taking out laundry
Press the Start / Pause button to switch the machine to
pause mode. The programme follow-up light of the relevant
step during which the machine was switched into the pause
mode will flash. Wait until the Loading Door can be opened.
Open the Loading Door and add or take out the laundry.
Close the Loading Door. Make changes in auxiliary functions,
temperature and speed settings if necessary. Press Start /
Pause button to start the machine.
4.16 Canceling the programme
To cancel the programme, turn the Programme Selection
knob to select another programme. Previous programme
will be canceled. End / Cancel light will flash continuously to
notify that the programme has been canceled.
Your machine will end the programme when you turn the
Programme Selection knob; however, it does not drain the
water inside. When you select and start a new programme,
the newly selected programme will start depending on the
step the previous programme was canceled in. For example,
it may take in additional water or continue to wash with the
water inside.
C
Depending on the step where the programme was
canceled in, you may have to put detergent and softener
again for the programme you have selected anew.
4.17 Your machine is equipped
with a "Standby Mode"
In case of not starting any programme or waiting without
making any other operation when the machine is turned
on by On/Off button and while it is in selection step or if
no other operation is performed approximately 2 minutes
after the programme you selected has come to an end, your
machine will automatically switch to energy saving mode.
Display brightness will decrease. In case of rotating the
Programme Selection knob or pressing any button, lights will
restore to their previous condition. This is not a fault.
5 Maintenance and cleaning
Service life of the product extends and frequently faced
problems decrease if cleaned at regular intervals.
5.1 Cleaning the detergent drawer
Clean the detergent drawer at regular intervals (every
4-5 washing cycles) as shown below in order to prevent
accumulation of powder detergent in time.
72 / EN
1. Press the dotted point on the siphon in the softener
compartment and pull towards you until the compartment
is removed from the machine.
C
If more than normal amount of water and softener
mixture starts to gather in the softener compartment, the
siphon must be cleaned.
2. Wash the detergent drawer and the siphon with plenty of
lukewarm water in a washbasin. Wear protective gloves
or use an appropriate brush to avoid touching of the
residues in the drawer with your skin when cleaning.
3. Insert the drawer back into its place after cleaning and
make sure that it is seated well.
If your detergent drawer is the one indicated in the following
figure:
C
Lift the rear part of the siphon to remove it as illustrated.
After performing the above mentioned cleaning
procedures, replace the siphon back to its seating and
push its front section downwards to make sure that the
locking tab engages.
5.2 Cleaning the loading door and the drum
Residues of softener, detergent and dirt may accumulate in
your machine in time and may cause unpleasant odours and
washing complaints. To avoid this, use the Drum Cleaning
programme. If your machine is not featured with Drum
Cleaning programme, use Cottons-90 programme and
select Additional Water or Extra Rinse auxiliary functions
as well. Run the programme without any laundry in the
machine. Before starting the programme, put max. 100
g of powder anti-limescale into the main wash detergent
compartment (compartment nr. 2). If the anti-limescale is in
tablet form, put only one tablet into compartment nr. 2. Dry
the inside of the bellow with a clean piece of cloth after the
programme has come to an end.
C
Repeat Drum Cleaning process in every 2 months.
C
Use an anti-limescale suitable for the washing machines.
After every washing make sure that no foreign substance is
left in the drum.
If the holes on the bellow shown in the figure is blocked,
open the holes using a toothpick.
Washing Machine / User's Manual
Werbung
Inhaltsverzeichnis
