Makita DFL082F Betriebsanleitung Seite 6

NOTE:
• If the indicator lamp does not turn on or flicker when
charging, the battery may be faulty. In this case, ask
your local service center.
When using
When the tool is switched on, the lamps will light to indi-
cate the remaining battery capacity. When the tool is
switched off, the light goes out after approx. 5 seconds.
When pushing the check button with the tool switched
off, the indicator lamps turn on for approx. 5 seconds to
show battery capacity.
If the orange lamp flickers, the tool stops because of little
remaining battery capacity (Auto-stop mechanism).
Charge the battery cartridge or use a charged battery
cartridge at this time.
When the tool is used with the battery that has not been
used for a long time and is switched on, no lamps may
light up. The tool stops because of little remaining battery
capacity at this time. Charge the battery properly.
Switch action (Fig. 3)
CAUTION:
• Before inserting the battery cartridge into the tool,
always check to see that the switch trigger actuates
properly and returns to the "OFF" position when
released.
To start the tool, simply pull the switch trigger. Release
the switch trigger to stop.
LED indicator / Beeper
LED indicator / Beeper on the tool shows the following functions.
Function
Auto-stop fastening
Delayed re-start
Warning against
insufficient fastening
Warning for battery
cartridge capacity
Checking the
remaining battery
capacity, Autostop
Check the LED indi-
cator, lamp and
beeper operation
Anti-reset of control-
ler
6
Status
This function works when the tool has
reached the preset fastening torque
and normal tightening has been com-
pleted. This helps overtightening to
be avoided.
For approximately one second after
auto-stop fastening, the tool does not
start even if the switch trigger is
pulled.
Insufficient fastening has been per-
formed when the switch trigger has
released before reaching the preset
fastening torque.
This indicates the appropriate time to
replace the battery cartridge when
the battery power becomes low.
This function works when the battery
power is almost used up. At this time,
tool stops immediately.
This function works to check the
proper operation of the LED indicator,
lamp and beeper when a battery car-
tridge has been inserted into the tool.
This function works when an abnor-
mal drop of the battery voltage occurs
for some reason, and the tool stops.
Reversing switch action (Fig. 4)
CAUTION:
• Always check the direction of rotation before operation.
• Use the reversing switch only after the tool comes to a
complete stop. Changing the direction of rotation
before the tool stops may damage the tool.
• When not operating the tool, always set the reversing
switch lever to the neutral position.
This tool has a reversing switch to change the direction
of rotation. Depress the reversing switch lever from the A
side for clockwise rotation or from the B side for counter-
clockwise rotation.
When the reversing switch lever is in the neutral position,
the switch trigger cannot be pulled.
Lighting up the lamps (Fig. 5)
CAUTION:
• Do not look in the light or see the source of light
directly.
Pull the switch trigger to light up the lamp. The lamp
keeps on lighting while the switch trigger is being pulled.
The light automatically goes out 10 seconds after the
switch trigger is released.
NOTE:
• Use a dry cloth to wipe the dirt off the lens of lamp. Be
careful not to scratch the lens of lamp, or it may lower
the illumination.
Status of the LED indicator/beeper
LED indicator
Lights up in
green for
approximately
one second.
Lights up in red. A long beep
Flickers in red A series of long
slowly. beeps
Lights up in red. A long beep
Lights up first in
green, next red.
A series of very
(And then the
short beeps
lamp comes
on.)
Flickers in red
A series of short
and green alter-
beeps
natively.
Action to be
taken
Beeper
— —
Retighten the
screw.
Replace the
battery with fully
charged one.
Replace the
battery with fully
charged one.
—
Replace the
battery with fully
charged one.