Transporting The Chainsaw; Before Starting Up; Tensioning The Saw Chain; Filling In Chain Oil (See Fig. 9) - Einhell Royal 45.015.50 Bedienungsanleitung

Anl REK 2040 WK SPK1:_
In order to prevent kick-back, please follow these
safety instructions:
Never start cutting with the tip of the chain bar!
Always keep a close eye on the tip of the chain
bar!
Never cut with the tip of the chain bar! Be
careful, when continuing cuts you are already
working on!
Always start cuts with the chainsaw already run-
ning!
Make sure that the saw chain is always properly
sharpened.
Never cut through more than one branch at a
time! When lopping off branches, be careful not
to touch any other branches.
When cross-cutting, pay attention to trunks stan-
ding very close to each other. If possible use a
sawing trestle.

5. Transporting the chainsaw

Before transporting the chainsaw, always remove the
plug from the power socket and slide the chain guard
over the rail and chain. If several cuts are to be per-
formed with the chainsaw, the saw must be switched
off between cuts.

6. Before starting up

The voltage and current supply must comply with the
ratings on the type plate. Before commencing work,
always check that the chainsaw works properly and
is safe to operate. Check also that the chain lubrica-
tion and the oil gauge are in good working order (see
Fig. 9). When the oil level is approx. 5 mm from the
bottom mark (marked with "Min" in the illustration),
you must top up with oil. When the oil level is above
this mark you can work without worry.
Switch on the chainsaw and hold it above light-col-
ored ground. Be careful not to allow the chainsaw to
touch the ground. For safety reasons it is best to
keep a clearance of at least 20 cm. If you now see
growing traces of oil, the chain lubrication system is
working correctly. If there are no traces of oil at all,
try cleaning the oil outlet, the upper chain tensioning
borehole and the oil duct.
7. Assembling the chain bar and saw
chain (see Fig. 2/3)
Make sure that the power plug is disconnected
from the power supply!
- Important: The front finger guard (1) must
always be in the top (vertical) position.
16.01.2007 8:48 Uhr Seite 17
The chain bar and saw chain are delivered separate-
ly. To assemble, first unscrew the fastening screw
(12) and the screw (16) by turning them counter-
clockwise and remove the brake housing hood (10).
To prevent injury on the sharp cutting edges, always
wear gloves when assembling, tensioning and
checking the chain. Before assembling the chain
bar with the saw chain, check the cutting direc-
tion of the teeth (see Fig. 2)! Hold the chain bar
(15) vertically with the tip pointing upwards and put
on the saw chain (14), beginning at the tip of the bar.
Then assemble the chain bar with the saw chain
as follows: Place the chain bar with the saw chain
on the bar pin (B) so that the chain tensioning wheel
(A) faces outwards. Place the saw chain round the
chain wheel (C). Twist the chain tensioning wheel
clockwise to pretension the chain. Reattach the chain
wheel cover (10) and gently tighten the fastening
screw (12).

8. Tensioning the saw chain

Always pull out the power plug before doing any
work on the machine!
Wear safety gloves!
Make sure the saw chain (14) is inside the guide
groove of the chain bar (15)! You can now tension
the chain correctly by turning the chain tensioning
wheel (11) clockwise (turning counterclockwise will
loosen the chain). Then tighten the fastening screw
(12) and screw in the screw (16). Check the chain
tension again (see Fig. 10). Do not tension the
chain too tightly. When cold, it should be possible to
lift the chain in the middle of the chain bar approx. 3
mm. When warm, the saw chain will expand and
slacken. There is a danger of the saw chain jumping
off the rail altogether.
Retension if necessary. If the saw chain is reten-
sioned when hot, it must be loosened again when
the sawing work has been completed. Otherwise, the
contraction which takes place as the chain cools
would result in excessively high tension. A new saw
chain requires a running-in period of approx. 5 min-
utes. Chain lubrication is very important at this stage.
After running in, check chain tension and retension if
necessary.

9. Filling in chain oil (see Fig. 9)

To prevent dirt getting inside the tank, clean the oil
tank cap (C) before opening. Check the contents of
the oil tank during sawing work by checking the oil
gauge (D). Close the oil tank cap (C) tightly and wipe
away any spills.
GB
17