Before Use; Accessories - Silverline 943792 Bedienungsanleitung

Before Use

Fitting collets
Note: This hobby tool is supplied with two Collets (8 & 9), in order to fit accessories with different
shaft diameters (see 'Specification').
WARNING: ALWAYS fit the correct collet that precisely matches the shaft diameter of the
accessory you wish to use.
1. Remove the Collet Nut (1) by depressing the Spindle Lock Button (3) and rotating it anticlockwise
until it can be removed from the spindle
Note: It may be necessary to use the supplied collet spanner to loosen the Collet Nut (1).
2. Remove the brass Collet (8 or 9), and replace with collet of the required size
3. Refit the Collet Nut, depress the spindle lock button and rotate the Collet Nut clockwise, to secure
it on the spindle
Fitting accessories
WARNING: Ensure the tool is switched off and disconnected from the power supply, before
fitting or removing accessories.
1. Loosen the Collet Nut (1) by depressing the Spindle Lock Button (3) and rotating the Collet Nut
anticlockwise
Note: It may be necessary to use the supplied collet spanner to loosen the Collet Nut (1).
2. Place the accessory required into the collet
WARNING: Ensure the correct Collet (8 or 9) for the accessory shaft diameter has been fitted.
3. Depress the spindle lock button and rotate the Collet Nut clockwise, to secure the accessory in the
collet
WARNING: Never fit any attachment with a maximum speed lower than the no load speed
of the machine.
Operation
WARNING: ALWAYS wear protective equipment including eye protection when operating
this tool.
Switching ON and OFF
1. Start the hobby tool by moving the ON/OFF Switch (6) to the '1' position
2. To stop the tool, move the switch to the '0' position
Adjusting tool speed
WARNING: ALWAYS set the speed according to the requirements of the accessory fitted and the
material of the workpiece.
• Use the Speed Control Dial (4) to control the rotation speed
Note: The higher the number on the dial the faster the spindle rotates.
Handling
WARNING: Always ensure the workpiece is adequately secured using clamps and/or a vice at
all times. Do not attempt to use this tool without sufficiently securing the workpiece first.
• Hold the tool securely, keeping hands well away from rotating parts. For most purposes, it is most
convenient to grip the tool like a pen
• If possible hold the tool with both hands when performing cutting operations
• Practice using the tool with scrap material before starting a job. Be aware that different
accessories will require different techniques, and may require different speed settings
• Applying excess pressure does not result in faster or more efficient performance. If the pressure
applied to the tool has a noticeable effect on the speed of the tool then reduce the pressure.
Overloading the tool will reduce its service life
• Always ensure that material is secure. If appropriate use a vice or clamp to hold the work

Accessories

• A full range of hobby tool accessories including a flexible shaft, vices and assorted accessory kits
is available from your Silverline stockist
• Spare parts can be obtained from toolsparesonline.com
Product description
Rotary Tool Accessory Kit 216pce
Rotary Tool Accessory Kit 105pce
Rotary Tool Flexi Drive Shaft
Rotary Tool Telescopic Hanging Stand
Multipurpose Cutting Kit 4pce
Tile Cutting Spiral Saw Bit
Rotary Tool Loose Leaf Buffing Kit 4pce
DIY 135W Multi-Function Rotary Tool
Maintenance
WARNING: Ensure the tool is switched off and disconnected from the power supply, before
cleaning or carrying out maintenance.
Cleaning
WARNING: ALWAYS wear protective equipment including eye protection and gloves when
cleaning this tool.
• Keep your tool clean at all times. Dirt and dust will cause internal parts to wear quickly, and
shorten the device's service life
• Clean the body of your machine with a soft brush, or dry cloth
• Never use caustic agents to clean plastic parts. If dry cleaning is not sufficient, a mild detergent
on a damp cloth is recommended
• Water must never come into contact with the tool
• Ensure the tool is thoroughly dry before using it
• If available, use clean, dry, compressed air to blow through the ventilation holes (where
applicable)
Maintaining the collet
Note: Collets are precisely engineered components. They need to remain undamaged, in order to
provide secure hold of the inserted accessories. If properly maintained collets will provide years
of service.
• Remove the Collet Nut (1) and Collet (8 or 9) in regular intervals and/or after heavy use, and
clean thoroughly. Also remove swarf and dust from around the spindle and thread, using a soft
brush and/or compressed air
WARNING: DO NOT use sharp implements, such as pins or screwdrivers to remove deposits
from inside or around the Collet (8 or 9).
Brushes
• Over time the carbon brushes inside the motor may become worn
• Excessively worn brushes may cause loss of power, intermittent failure, or visible sparking
• To replace the brushes, remove the Brush Access Plugs (7) from both sides of the machine.
Remove the worn brushes and replaced with new. Replace Brush Access Plugs. Alternatively, have
the machine serviced at an authorised service centre
Contact
For technical or repair service advice, please contact the helpline on (+44) 1935 382 222
Web: silverlinetools.com/en-GB/Support
Address:
Toolstream Ltd.
Boundary Way
Lufton Trading Estate
Yeovil, Somerset
BA22 8HZ, United Kingdom
Storage
• Store this tool carefully in a secure, dry place out of the reach of children
Disposal
Always adhere to national regulations when disposing of power tools that are no longer functional
and are not viable for repair.
• Do not dispose of power tools, or other waste electrical and electronic equipment (WEEE), with
household waste
• Contact your local waste disposal authority for information on the correct way to dispose of
power tools
silverlinetools.com
7