Electrical Connection; Montaje Seguro - Siemens ER3A6BB70 Montageanleitung

Electrical connection

¡ This appliance is type Y: The connection cable
must only be replaced by technical customer ser-
vice and not by the user. The cable type and the
minimum cross section must be respected.
¡ The hobs are supplied with a power cord with or
without a plug.
¡ Only connect appliances that are fitted with a plug
to a correctly installed socket with protective earth
conductor.
¡ If the plug is not accessible to the user, an all-pole
isolating safety switch with a minimum contact
opening of 3 mm must be provided.
→ Fig.
10
Converting the gas type
If the country's regulations allow, this appliance can
be adapted to other types of gas, if these are listed
on the rating plate.
You can find the right parts in the bag that is sup-
plied with the appliance or you can obtain them from
customer service. The table → Fig.
right combination for the relevant burner and gas
type.
Standard-output burner
High-output burner
Dual-wok multi-crown burner
¡ 1 - Outer flame
¡ 2 - Inner flame
Tools
Contact technical customer service to purchase the
relevant tools.
Removal lever
Adjusting the taps
Turn the rotary knobs to the minimum power posi-
1.
tion and pull them out.
With the tip of the screwdriver, push down on the
2.
flexible rubber holder to access the bypass screw.
→ Fig.
11
Never remove the sealing ring. The sealing rings
prevent liquids and dirt from finding their way into
the appliance and impairing its ability to function
properly.
When adjusting the bypass screws (M), refer to
3.
the table → Fig. .
23
A: Firmly tighten the bypass screws.
‒
B: The bypass screws must be flush with the fit-
‒
ting.
→ Fig.
12
Removing the upper part of the appliance (glass
plate with cut-out profiles)
Remove the pan supports, burner caps, distribut-
1.
ors and rotary knobs.
Undo the screws on the burners.
2.
→ Fig.
13
Move the removal lever under the metal cut-out
3.
profile into the area marked for the hob model
and loosen the front clip fastener.
→ Fig.
14
Only use the lever under the cut-out profiles or the
metal frame of the hob.
Carefully lift the glass plate with the cut-out pro-
4.
files to release the rear clip fastener.
Replacing the nozzles
Remove all pan supports, burner caps and distrib-
1.
utors.
2.
Replacing the outer flame nozzle on the multi-crown
burner
Requirement: The upper part of the appliance has
been removed. → "Removing the upper part of the
appliance (glass plate with cut-out profiles)",
Page 11
1.
2.
3.
shows the
23
4.
Replacing the inner flame nozzle on the multi-crown
burner
Requirement: The upper part of the appliance has
been removed. → "Removing the upper part of the
appliance (glass plate with cut-out profiles)",
Page 11
1.
2.
483196
3.
4.
Reinstalling the appliance
▶
Checking if equipment is working
1.
2.
Documenting the gas type conversion
▶

Montaje seguro

Tener en cuenta estas indicaciones de seguridad al
montar el aparato.
¡ Lea atentamente estas instrucciones.
¡ Las imágenes representadas en estas instruccio-
¡ Solamente un montaje profesional conforme a las
Replace the nozzles using the appropriate wrench
and tighten them carefully to guarantee the seal.
→ Fig.
15
Ensure that the nozzle does not become detached
during removal or fastening.
To gain access to the main nozzle, loosen the
fastening screw and pull the sleeve
→ Fig.
16
Remove the nozzle by turning it anti-clockwise
and screw in the new outer flame nozzle
→ Fig.
17
Set the spacing of the adjustment sleeve for the
air supply to dimension Z, as shown in the table
→ Fig. .
23
→ Fig.
18
Tighten the fastening screw.
→ Fig.
19
Unscrew the tube by applying pressure to the
sleeve in the opposite direction to hold it in place
and pulling the tube out of the sleeve
→ Fig.
20
Remove the sleeve.
→ Fig.
21
Remove the inner flame nozzle from the sleeve
and screw in the new nozzle.
→ Fig.
22
Screw the sleeve and the tube back into their ori-
ginal position.
Install the appliance components in reverse order.
Check that turning the rotary knob between the
position for maximum power and the position for
minimum power does not cause the burner to go
out or result in backfire.
If the gas flow from the burner is not correct, in
the table → Fig. , check whether the nozzle and
23
the position of the bypass screw are correct.
Attach the sticker showing the new gas type near
to the rating plate.
es
nes tienen carácter orientativo.
instrucciones de montaje puede garantizar un uso
seguro del aparato. El instalador es responsable
del funcionamiento perfecto en el lugar de instala-
ción.
back.
⁠
⁠ .
⁠ .
11