Herunterladen Inhalt Inhalt Diese Seite drucken

Safety Regulations; Layout And Items Supplied - EINHELL TC-EH 500-18 Originalbetriebsanleitung

Inhaltsverzeichnis

Werbung

Verfügbare Sprachen

Verfügbare Sprachen

  • DEUTSCH, seite 1
Danger!
When using the equipment, a few safety pre-
cautions must be observed to avoid injuries and
damage. Please read the complete operating
instructions and safety regulations with due care.
Keep this manual in a safe place, so that the in-
formation is available at all times. If you give the
equipment to any other person, hand over these
operating instructions and safety regulations as
well. We cannot accept any liability for damage
or accidents which arise due to a failure to follow
these instructions and the safety instructions.

1. Safety regulations

Danger!
Read all safety regulations and instructions.
Any errors made in following the safety regula-
tions and instructions may result in an electric
shock, fi re and/or serious injury.
Keep all safety regulations and instructions
in a safe place for future use.
1. Always check that the mains voltage is iden-
tical to the voltage quoted on the rating plate.
In the event that the mains voltage is not
suitable, it may cause the machine to work
abnormally and thus result in personal injury.
2. The power supply must be earthed and be
secured by a residual current operated circuit
breaker (RCCB).
3. Do not attempt to lift loads that exceed the
rated load.
4. Use the machine only for the purpose for
which it is designed. Never lift personnel
using the cable hoist.
5. Do not pull the power cable in order to pull out
the plug. Protect the power cable from heat,
oil and sharp edges.
6. Never attempt to raise fi xed or jammed loads.
7. Pull out the plug when the cable hoist is not in
use.
8. Keep children and other unauthorized per-
sons away from the machine.
9. Do not pull loads sideways or from one side.
Do not allow the load to swing.
10. Ensure that the hook moves in the same di-
rection as shown on the control switch.
11. Check the cable hoist at regular intervals for
signs of damage. The control switch must be
in good condition.
12. Have repair and servicing work carried out
only by authorized workshops by a trained
Anl_TC_EH_500_18_SPK7.indb 14
Anl_TC_EH_500_18_SPK7.indb 14
GB
electrician. Repair work must only be carried
out by a trained electrician, otherwise the ma-
chine may cause accidents.
13. Do not switch the machine on and off quickly
(inching mode).
14. Always concentrate fully when operating the
cable hoist.
15. Do not stand or work under the raised load.

2. Layout and items supplied

2.1 Layout (Fig. 1/2)
1. Fastening bar
2. Fastening hole for hook
3. Drum
4. Lever for maximum cable length
5. Automatic stop mechanism lever
6. Steel cable
7. Cut-out weight
8. Hook
9. Emergency Stop switch
10. Pushbutton
11. Remote control
12. Power cable
13. Control cable
14. Motor
15. Return roller
16. Additional hook
17. Cable for remote control
2.2 Items supplied
Please check that the article is complete as
specifi ed in the scope of delivery. If parts are
missing, please contact our service center or the
sales outlet where you made your purchase at
the latest within 5 working days after purchasing
the product and upon presentation of a valid bill
of purchase. Also, refer to the warranty table in
the service information at the end of the operating
instructions.
Open the packaging and take out the equip-
ment with care.
Remove the packaging material and any
packaging and/or transportation braces (if
available).
Check to see if all items are supplied.
Inspect the equipment and accessories for
transport damage.
If possible, please keep the packaging until
the end of the guarantee period.
- 14 -
19.06.2020 12:37:00
19.06.2020 12:37:00

Werbung

Inhaltsverzeichnis
loading

Diese Anleitung auch für:

22.551.45

Inhaltsverzeichnis