Product Description And Specifications - Bosch GWS 2000 Professional Originalbetriebsanleitung

18 | English
Product Description and
Specifications
Read all the safety and general instructions.
Failure to observe the safety and general in-
structions may result in electric shock, fire
and/or serious injury.
Please observe the illustrations at the beginning of this oper-
ating manual.
Intended use
The power tool is intended for cutting, roughing and brush-
ing metal and stone materials without the use of water.
A special protective guard for cutting must be used when
cutting bonded abrasives.
Sufficient dust extraction must be provided when cutting
stone.
With approved abrasive tools, the power tool can be used for
sanding with sanding discs.
Product Features
The numbering of the product features refers to the diagram
of the power tool on the graphics page.
(1) Spindle lock button
(2) On/off switch
(3) Auxiliary handle (insulated gripping surface)
Technical Data
Angle grinder
Article number
Rated power input
Power output
Rated speed
Max. grinding disc diameter
Grinding spindle thread
Max. thread length of grinding spindle
Weight according to EPTA-Procedure 01:2014
– with additional low-vibration auxiliary handle
– with standard auxiliary handle
Protection class
The specifications apply to a rated voltage [U] of 230 V. These specifications may vary at different voltages and in country-specific models.
When switching on power tools with starting current limitation, the voltage drops briefly. Interference with other equipment may occur in the
event of unfavourable conditions in the electricity supply. Malfunctions are not expected if the impedances in the electricity supply are below
0.25 ohms.
Noise/Vibration Information
Noise emission values determined according to
EN 60745-2-3.
Typically, the A-weighted noise level of the power tool is:
Sound pressure level 91 dB(A); sound power level 102
dB(A). Uncertainty K=3 dB.
Wear hearing protection
1 609 92A 43A | (28.11.2018)
(4) Grinding spindle
(5) Protective guard for grinding
(6) Locking screw for protective guard
(7) Mounting flange with O‑ring
A)
(8) Grinding disc
(9) Clamping nut
(10) Two-pin spanner for clamping nut
(11) Quick-clamping nut
A)
(12) Carbide grinding head
(13) Protective guard for cutting
A)
(14) Cutting disc
A)
(15) Hand guard
A)
(16) Spacer discs
A)
(17) Rubber sanding pad
A)
(18) Abrasive disc
A)
(19) Round nut
A)
(20) Cup brush
(21) Extraction guard for cutting with a guide block
A)
(22) Diamond cutting disc
(23) Handle (insulated gripping surface)
A) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
GWS 2000
3 601 HB7 0..
W 2000
W 1280
-1
min 8500
mm 180
M 14
mm 25
kg 5.1
kg 5.0
/ II
Total vibration values a (triax vector sum) and uncertainty K
h
determined according to EN 60745-2-3:
Surface grinding (roughing):
2 2
a =7,0 m/s , K=1,5 m/s ,
h
Grinding with abrasive disc:
2 2
a =3,5 m/s , K=1,5 m/s .
h
The vibration level given in these instructions has been
measured in accordance with a standardised measuring pro-
A)
A)
A)
A)
GWS 2000
3 601 HB8 0..
2000
1280
6500
230
M 14
25
5.4
5.3
/ II
Bosch Power Tools