Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
A. Point -
To display a Point value on the Status
Line, refer to Figure 3-24 and perform the following
steps:
B R O W S
V IE W
0 4 /1 6 /9 7
P re s s D IS P la y Ke y
D IS P
0 4 /1 6 /9 7
P o in t
U s e U p o r D o w n Ar ro w
A la rm s
K e ys to s cr o ll h ig h lig h t
J u n ctio n Te m p
to P o in t a n d p re ss E N TE R .
V er sio n
M e d ia S ta tus
E N TE R
04 /1 6 /9 7
Press the button cor esponding
to th e P o in t N u m b e r d es ired
an d p res s E N T E R o n th e M en u
B ut to n B a r o r p res s E X IT in th e
dia lo g b ox to le av e t he d ia log
bo x w it ho ut m a k ing c h an g es .
E N TE R
0 4 /1 6 /9 7
1 0 3 7 1 7 M A
Figure 3-24 Display Point Flow Chart
1. Press the DISPL Key and then use the UP (↑)
or DOWN (↓) Arrow Keys to highlight "Point".
Press ENTER and "point? X" will display.
2. Use the Numeric Keypad to select the point
number you wish to display and press ENTER.
The following responses may be displayed:
•
Point Number, Value, Engineering Units
or
•
Point Number, Value and Alarm Status
(Status Line showing Alarm)
3. The following responses may be displayed if
there is a problem with the point displayed:
•
Not Found - Point requested does not exist in
the database.
•
Bypassed-
Point requested is bypassed.
•
TCBO -
Thermocouple Burnout
•
Invalid -
Incorrect
Basepoints
•
Data of calculated points exceed
Overflow -
limit of floating point
function.
•
Overrange - Point
exceeds the range setup.
Siemens AG C79000-G7374-C211-01
SIREC D Manual
P re ss M E N U Ke y
JO G
M E N U
4 :5 9 :2 9
P R O G
F U N C
EX IT
4 :5 9 :2 9
E X IT
4 :5 9 :2 9
Point? 1
A
7
8
9
B
4
5
6
C
3
2
1
E X IT
4 :5 9 :2 9
E X IT
or
Abnormal
math
measurement
signal
To have the point information come up
automatically at power up and be the de-
fault display, use the Display Programming
option to set "Points" as the Powerup dis-
play default. The "Autojog" default option
will cycle through all points. Refer to Chap-
ter 4.
B. Alarms -
To display an Alarm status on the
Status Line, Refer to Figure 3-25 and perform the
following:
B R O W S
V IE W
0 4 /1 6 /9 7
P re s s D IS P la y K e y
D IS P
0 4 /1 6 /9 7
P o in t
U s e U p o r D o w n A rro w
V e rs io n
K ey s to s cr o ll H ig h lig h t B a r
M e d ia S ta tu s
to A la rm s a n d p re s s E N TE R .
E N T E R
0 4 /1 6 /9 7
1 0 3 71 8 M A
Figure 3-25 Display Alarms Flow Chart
1. Press the DISPL Key and use the UP (↑) or
DOWN (↓) Arrow Keys to highlight "Alarms".
2. Press ENTER and the Status Line display will
show the status of the alarms.
•
If no alarms are present the display will show
"NO ALARMS".
•
If more than one alarm is active, the display
will cycle through all active alarms.
•
If the Alarm check option is turned off, this
will be indicated on the display as "ALM
CHKS OFF"
To have the Alarm information come up
automatically at power-up and be the de-
fault display, use the Display Programming
option to set "Alarms" as the Power-up Dis-
play default. Refer to Chapter 4.
Operation
NOTE
P re s s M E N U K ey
J O G
M E N U
4 :5 9 :2 9
P R O G
F U N C
4 :5 9:2 9
4:5 9 :2 9
NOTE
E X IT
E X IT
3-13
Werbung
Kapitel
Inhaltsverzeichnis
