Hamax Pluto Medium Bedienungsanleitung Seite 11

GETTING STARTED - INSTALLATION
[1] Packaging content
• Trailer body with Push Bar [1a]
• Quick release wheel (2x) [1b]
• Stroller wheel [1c]
• Wheel guards with screw (2x) [1d]
• Safety flag [1e]
• Rear light [1f]
• Bicycle arm with hitch [1g]
• Keys (2x) [1h]
• User manual
[3] Unfolding the trailer
Important: Make sure to unfold the trailer correctly!
• Grab the frame [3a] in the middle and pull it upwards you. The trailer now unfolds until the locking pins lock in the fold locks [3b]
on both sides automatically with a clicking sound. Push in opposite direction to verify both locks are locked.
[4] Suspension adjustment
• The suspension kan be adjusted to the load of the trailer by fitting the quick release wheels in one of three positions [4c] on the
rear suspension arms [4a]
• Each wheel position corresponds to a specific dog weight/trailer load.
• Determine the correct wheel axle hole position [4c] for the weight of your dog using table [4d]
• The suspension arm plugs [4b]can be removed by pinching together the snap hook end from the back of the supension arm.
• (Re)Place the supension arm plugs in the unused wheel axle holes on the left and right suspension arms.
• Make sure the left and right suspension arms [4a] use the same wheel axle positions [4c].
[5] Mounting the quick release wheels
• For first time assembly, remove the cap that is protecting the wheel axle.
• Ensure that the parking brake [2i] is not engaged and that the wheel axle is clean.
• Press the push button [5a] and insert the wheel axle into the wheel axle hole on the suspension arm, then release the button.
• Verify that the wheel is securely fastened by pulling the wheel without pusing the push button [5a]
• Note that there is a left and a right wheel for the trailer. The rotation direction is indicated on the side of the tires. Mount the
wheels with the rotation direction matching the driving direction according to the arrow in the picture.
[6] Mounting the stroller wheel (see point 13 to remove the stroller wheel)
• Insert the stroller wheel [6a] into the central connection point [6b] until it clicks in place. Verify that the stroller wheel is
securely fastened by pulling the stroller wheel.
• Do not use the stroller wheel indoors as it could leave marks on the floor.
[7] Assembly of the wheel guards
• The trailer has a left and right wheel guard [7a] that are both required to assemble for safety.
• Insert the wheel guard screw [7b] into the hole in the wheel guard as shown.
• Position the left wheel guard against the left frame tube with the narrow part to the front of the trailer and the cavities facing
down. The two pins on the wheel guard should fall into accomodating holes on the frame.
• Tighten the screw [7b] using a Philips head screw driver by turning clockwise until tight.
• Repeat the above procedures for the right wheel guard.
[8] Attaching the hitch on your bicycle
• Remove quick-release or nut [8a] from the left side of your bicycle' s rear wheel axle. If your bicycle has a dropout, place the
rotation-lock washer [8c] with the bend of the washer fitting inside the drop out. This helps keeping the hitch at the correct
angle, but the hitch can also be attached without it.
• Place hitch [8b] between quick-release or nut and frame. If rotation-lock washer [8c] was installed, match the ribs on the
washer, to the grooves on the hitch. Make sure the hitch orientation [8b] is simlar as shown.
• Tighten the quick-release or nut [8a] back on the axle according to the bicycle manufacturer' s instructions.
p. 14
[2] Product overview
• Pushbar [2a]
• Pushbar height adjustment paddels [2b]
• Mesh doors [2c]
• Suspension [2d]
• Wheel guards [2e]
• Bicycle arm connection [2f]
• Luggage pocket [2g]
• Fold locks [2h]
• Parking Brake [2i]
• Rear Entrance Mesh and Cover [2j]
• Top fabric [2k]
• Bottom fabric [2l]
• Interior Fabric [2m] with bicycle arm pocket [2n]
• Leash attachment Points (inside)[2o]