Backlight; Maximum And Minimum Values - TFA 35.1135 Bedienungsanleitung

TFA_No. 35.1135_Anleit_04_23
Wireless weather station
• During nighttime, the atmospheric interference is usually less severe and recep-
tion is possible in most cases. A single daily reception is adequate to keep the
accuracy deviation under 1 second.
5. Operation
• The device will automatically quit the setting mode if no button is pressed for a
long period of time.
• Press and hold CH/+ or MEM/- button in the setting mode for fast running.
5.1 Manual setting of the clock
• Press and hold DISPLAY/SET button for three seconds.
• The 24- and 12 HR system (default: 12 Hr) will be flashing.
• Press the CH/+ or MEM/- button in normal mode to choose between 24- and 12
HR system (AM or PM appears on the display).
• Press the DISPLAY/SET button to make the settings in the following sequence: the
hours, the minutes, the seconds and the time zone (default: 00). Press the CH/+ or
MEM/- button to adjust it.
• Confirm with the DISPLAY/SET button.
• The manually set time will be overwritten by the DCF time when the signal is
received successfully.
5.1.1 Setting of the time zone
• In the setting mode you can make the time zone correction (-23/+23).
• The time zone correction is needed for countries where the DCF signal can be
received but the time zone is different from the German time (e.g. +1=one hour
later).
• Press the CH/+ or MEM/- button.
• Confirm with the DISPLAY/SET button.
5.2 Setting of the alarm time
• Press the ALARM/SET button in normal mode.
• AL and 12:00 (default) or the last adjusted alarm time appear on the display.
• The hour digits will be flashing.
• Press the MEM/- or CH/+ button to adjust hours.
• The alarm symbol appears on the display.
• Confirm the setting with the ALARM/SET button and set minutes in the same way.
• Press the ALARM/SET button again.
• The current time and the alarm symbol appear on the display.
• When the adjusted alarm time is reached, the alarm will ring.
22
04.04.2023 11:30 Uhr Seite 12
Wireless weather station
• The alarm symbol will be flashing.
• Press the ALARM/SET button to turn off the alarm.
• If the alarm is not stopped manually, the increasing alarm will automatically turn
off after two minutes and will be reactivated at the same time.
• When the alarm rings, press the SNOOZE/LIGHT button and the snooze function
will be activated.
• Once the snooze function will be activated, the alarm symbol will be flashing on
the display.
• The alarm will be interrupted for 5 minutes.
• Press the ALARM/SET button in normal mode to enter alarm function.
• Press the ALARM/SET button once more to turn off the alarm and snooze function.
• The alarm symbol disappears on the display.
5.3 Display
• Press the ALARM/SET button in normal mode, to show the alarm time.

5.4 Backlight

• Press the SNOOZE/LIGHT button to activate the backlight for five seconds.
6. Weather forecast (Fig. 3)
• The weather station has four different weather symbols (sunny, partly cloudy,
cloudy and rainy).
• The weather forecast relates to a range of 12 to 24 hours and indicates only a gen-
eral weather trend. For example, if the current weather is cloudy and the rain sym-
bol is displayed, it does not mean the product is faulty because it is not raining. It
simply means that the air pressure has dropped and the weather is expected to get
worse but not necessarily rainy. The accuracy is about 70 to 75%.
• The sun symbol also appears at night if there is a starry night.
7. Temperature and humidity

7.1 Maximum and minimum values

• Press the MEM/- button.
• MAX appears on the display.
• The highest temperature and humidity for indoor and outdoor are displayed since
the last reset.
• Press the MEM/- button again.
• MIN appears on the display.
23