Technical Data - Sygonix 2632392 Bedienungsanleitung

The product must only be connected to an easily accessible mains socket. The product
must be disconnected from the mains in case of danger.
Never connect or disconnect the product when your hands are wet.
Adapters must not be plugged into each other.
Only use the product with permanently installed mains sockets with protective earth con-
tacts. Do not plug the product into power strips or use extension cables.
Always lay cables such that they do not constitute a hazard to people and pets.
The product is only isolated from the mains when it is unplugged from the socket.
Never cover the product during use.
Consult a technician if you are not sure how to use or connect the product, or if you have
concerns about safety.
Maintenance, modifications and repairs must be carried out by a technician or a specialist
repair centre.
6 Getting started
Please note that the charging cable has two ends. The plug connects to the charging station,
while the socket connects to the electric vehicle.
Carefully read the instructions for the charging cable and the vehicle.
6.1 Starting charging
Stop the vehicle engine and set the gear lever to park.
Insert the Type 2 plug firmly into the socket at a suitable charging station (AC EVSE socket).
Plug the Type 2 socket into the electrical socket on the electric vehicle.
Lock your electric vehicle. The charging station (EVSE) will charge the vehicle.
May vary depending on the vehicle.
6.2 Stopping charging
Do not disconnect the plugs/connectors while the vehicle is charging.
Unplug the Type 2 plug from the charging station (AC EVSE socket) to interrupt the power
supply.
Remove the Type 2 socket from the vehicle.
Place the protective caps on the plugs/connectors and roll up the cable without bending it.
Pack the EV charging cable and store it in a suitable location.
7 Troubleshooting
7.1 The pins do not lock into place:
When inserting the cable, apply plenty of pressure until the pins are properly connected to the
EVSE or the electric vehicle.
7.2 The vehicle is not locked:
To start the charging process, the vehicle must be locked and switched off.
May vary depending on the vehicle.
8 Cleaning and care
This product does not require any maintenance. Never attempt to dismantle it. Disconnect
the product from the mains supply before cleaning. Dust in the connector can easily be
removed using a clean, soft brush and a vacuum cleaner. Do not use abrasive cleaning
agents, cleaning alcohol or other chemical solutions, as these could damage the casing,
impair operation or cause discolouration. To prevent scratch marks, do not press too stron-
gly on the surface when cleaning.
Use a damp cloth to clean the cable.
Remove the product from the mains and the connected load before cleaning.
Do not immerse the product in water.
9 Disposal
9.1 Product
All electrical and electronic equipment placed on the European market must be
labelled with this symbol. This symbol indicates that this device should be disposed
of separately from unsorted municipal waste at the end of its service life.
All owners of waste equipment are obliged to dispose of waste equipment separa-
tely from unsorted municipal waste. Before handing the old device to a collection
point, end users are required to separate old batteries which are not enclosed by
the old device, as well as lamps which can be removed from the old device without
any damage.
Distributors of electrical and electronic equipment are legally required to accept waste equip-
ment free of charge. Conrad provides the following return options free of charge (more details
on our website):
At our Conrad stores
At the collection points established by Conrad
At the collection points of public waste disposal agencies or at the collection systems set up
by manufacturers and distributors in accordance with the German Electrical and Electronic
Equipment Act.
The end user is responsible for deleting personal data on the old device before disposal.
Please note that in countries outside Germany, other obligations may apply to the return and
recycling of old devices.

10 Technical data

10.1 Power supply
Rated voltage ........................................... 230 V/AC, 50 Hz
10.2 Connected load/current
Connected load/current ............................ max. 3.6 kW, 16 A
Number of phases .................................... 1
Supply frequency ...................................... 50/60 Hz
10.3 Charging cable
Charging standard (connector) ................. Type 2
Charging standard .................................... Mode 3
Insulation resistance ................................. > 1000 MOhm
Terminal temperature rise ......................... < 50 K
Withstand voltage ..................................... 2000 V
Contact resistance .................................... 0.5 mOhm
Mechanical lifespan .................................. > 10,000x plug in/out when idle
Shock resistance ...................................... Fall from a height of 1 m; run over by
..................................................................
Housing .................................................... PC, flame retardant according to UL94 V-0
Cable material .......................................... TPU
Contacts ................................................... Copper alloy, silver-plated
Ingress protection ..................................... IP54
Certification standard ................................ IEC 62196-1 / IEC 62196-2
EV connector ............................................ IEC 62196 Type 2 (socket)
EVSE connector ....................................... IEC 62196 Type 2 (plug)
10.4 Miscellaneous
Cable length ............................................. 7 m
Weight ...................................................... 1686 g
Ambient conditions
Operating conditions ................................. -30 to +50 °C, max. 95% RH (non-condensing)
Storage conditions .................................... -30 to +50 °C, max. 95% RH (non-condensing)
Maximum operating altitude ..................... < 2000 m
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in
electronic data processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited.
This publication represent the technical status at the time of printing.
Copyright 2023 by Conrad Electronic SE.
Vehicles with a weight of max. 2 t.
*2632392_v2_0423_02_m_dh_en