Programming Procedure - Farfisa ALBA CV2124AB Bedienungsanleitung

111 Address of the Audio-Video Module.
112 Block address valid for all call buttons.
113 Automatic sequential allocation of device
address for all call buttons.
---------------------------------------------
121 Enable tone while electrical lock is open-
ing
122 Switching OFF the video signal while
electrical lock is opening.
123 Activate auxiliary relay with PB-GN con-
tact.
124 Sending door opened warning code.
128 Extend maximum talk time to 8 minutes.
---------------------------------------------
131 Electrical lock activation time.
132 Auxiliary relay activation time.
---------------------------------------------
142 Presence of door keeper exchangers
148 Auxiliary relay block address.
149 Auxiliary relay device address.
---------------------------------------------
151 Address of the first video camera asso-
ciated with the external unit (VM1).
152 Address of the second video camera as-
sociated with the external unit (VM2).
153 Address of the third video camera asso-
ciated with the external unit (VM3).
154 Address of the fourth video camera as-
sociated with the external unit (VM4).
155 Address of the fifth video camera asso-
ciated with the external unit (VM5).
156 Address of the sixth video camera asso-
ciated with the external unit (VM6).
157 Address of the seventh video camera
associated with the external unit (VM7).
158 Address of the eighth video camera as-
sociated with the external unit (VM8).
159 Selection of the main camera associated
with the Audio-Video module (TP).
---------------------------------------------
221 Block address for the single call button.
222 Device address for the single call button.
223 Block address for all buttons starting
from the one in the programming.
224 Automatic sequential assignment of
device addresses to call buttons starting
from the one in the programming.
---------------------------------------------
323 Muting the call in progress tone.
324 Closing the call when the door lock open-
ing command is received.
---------------------------------------------
411 Language of voice messages.
421 Volume of voice messages generated out
of conversation.
---------------------------------------------

Programming procedure

To carry out the programming, you need to:
Enter the programming mode following the
indications in the "Enter Programming Mode"
section, the symbol will start flashing
quickly notifying the operator that the device
is awaiting the programming code;
identify the programming code to use (see
table 1);
enter the three digits of the programming
code you intend to use following the
instructions in the "entering codes and
values" section;
press 1/ to confirm: you will hear a tone,
the symbol will stop flashing, and
the symbol will start to flash quickly
notifying the operator that the device is
awaiting the value;
enter the new value, following the
instructions in the "Entering Codes and
Values" section;
press 1/ to confirm: you will hear a tone
and the symbol will stop flashing and
the symbol will flash quickly, notifying
the operator that the device is awaiting a
new programming code;
continue by entering the code of another
programming or exit, following the
instructions in the "Exit Programming Mode"
section.
Return to factory setting of all parame-
ters of the Audio-Video Module except
for the addresses associated with the
call buttons (000 code)
With this programming, all module parameters
will return to their factory value (factory values
are listed at the beginning of the "Program-
ming" section). The addresses associated with
the call buttons will not be changed.
Enter code 000;
press button1/ to confirm;
Enter value 123;
press button 1/ , t o confirm, t he device emits
a tone and the , and
will light up for 2 sec. indicating that the
parameter values have returned to default
factory settings.
Attention: the single-button operation
mode (factory default) is not restored by
either this default procedure or the one
described in the next paragraph.
Return to factory settings of all the ad-
dresses associated with the call buttons
of the Audio-Video Module and any Addi-
tional Push-Buttons Modules (code 001)
With this programming, all of the Block and
Device addresses assigned to call buttons will
return to their factory value (factory values are
listed at the beginning of the "Programming"
section). The other parameters programmed
in the Audio-Video module will not be changed.
Enter code 001;
press button1/ to confirm;
Enter value 123;
press button 1/ , t o confirm, t he device emits
a tone and the
will light up for 2 sec. indicating that the
addresses associated with the call buttons
have returned to factory values.
Audio-Video Module Address (code 111)
It is possible to store the address of the Au-
dio-Video module (factory setting 231, ad-
dresses allowed between 231 and 253).
Enter code 111;
press button1/ to confirm;
enter the new address of the external unit;
press button1/ to confirm;
continue with the next programming or exit
programming.
Programming sequential addresses in
the call buttons (codes 112-113).
In extended range DUO systems, each user
must be identified by a Block Address (000
to 099) and a unique or Device Address (001
to 200), with the following programming it
is possible to assign to all call buttons of the
external unit (both the audio-video and any
additional push-button modules) a single
Block Address and, automatically, a sequential
incremental Device Address starting from the
button 1 of the audio-video module.
Attention: the sequential numbering will
symbols
be congruent with the previously selected
configuration of call buttons for the door
station (single-button or double-button),
see the example at the end of the section.
, and symbols
Mi 2585 - 15 -