Entering Programming Mode; Exit Programming Mode - Farfisa ALBA CV2124AB Bedienungsanleitung

Entering programming mode

Entering programming is only done with the
unit in standby mode. To enter programming,
you need to:
simultaneously hold pressed keys 2 and 4
for 4 seconds;
after the 4 sec. the module emits a tone and
the symbol starts flashing quickly;
within 5 seconds press buttons 1, 2, 3 and
4 sequentially, the symbol flashes
quickly and the module emits a tone every 4
sec. to indicate that you are in programming
mode.

Exit programming mode

To exit programming, you need to:
simultaneously keep pressed keys 2 and 4
for 4 sec.;
After 4 sec. the module emits a tone and the
symbol turns off.
Entering codes and values
To enter codes and values, use the keys 1/
and 2; their use is as follows:
1/ : This button is pressed to confirm the
entering of a code or to switch to
another programming phase.
2: This button is pressed to increase the
value of the digit to be entered. Press
the button a number of times equal to
the digit to be entered (digit 1=1 press,
digit 9=9 presses, digit 0=10 presses of
the button).
Button pressing is confirmed by a tone.
Notes on entering codes and values
- The codes and values to be entered must be
always formed by three digits (hundreds,
tens, and units); codes and values that are
composed of tens and units or units alone
must be completed by adding zeros. For
example, number 96 becomes 096 and
number 5 becomes 005.
- The digits must be entered one by one by
pressing "n" times the "2" button, where"
n "corresponds to the value of the digit to
be entered, followed by a pause of about 2
seconds to switch to the next digit (a tone
will indicate when switching to entering the
next digit). For example, to enter number 096
you need to:
- press the "2" button 10 times to enter the
- 14 - Mi 2585
digit 0 and wait for 2 seconds until you
hear a tone;
- press the "2" button 9 times to enter digit 9
and wait for 2 seconds until you hear a tone;
- press the "2" button 6 times to enter the
digit 6 and wait for 2 seconds until you
hear a tone.
Attention: after composing the number,
always remember to confirm the entry
by pressing the key 1/ .
Configuring call buttons of the Door Sta-
tion
With the following programming it is possible
to select t he configuration of t he buttons of t he
Door Station (default setting is single-button
mode).
Single-button or double-button
The audio-video module and the additional
button modules connected to it (up to 8) can
work as:
Single-Button Double-Button
P1 P1 P1
P3
P2 P2 P2
P4
P3 P3 P3
P9
P4 P4 P4
P10
P5 P5 P5
P11
P6 P6 P6
P12
To make the selection you need to:
Enter programming.
For single-button operation, simultane-
ously press for 4 sec. keys 1 and 2, the
module emits a tone and the 2 symbols
and are lit simultaneously for 2 sec.
For double-button operation, simulta-
neously press for 4 sec. keys 1 and 3, the
module emits a tone and the 2 symbols
and are lit simultaneously for 2 sec.
Exit programming.
Attention: the programming is active both
on the audio-video module and on all the
additional button modules connected to
it.
In the case of selecting single-button
operation, by default, the buttons will call
the following addresses:
P1
099
P2
100
P3
101
P4
102
P5
103
P6
104
In the case of selecting double-button
operation, by default, the buttons will call
the following addresses:
P3
101
P4
P1 P1
102
P2 P2 P9
107
P P5
P10
108
P P6
P11
P7 P
109
P8 P
P12
110
Programming of the Audio-Video Module
The programming of the Audio-Video Module
is carried out by entering the programming
code followed by its value; codes are shown
in table 1.
Table 1
Programming codes
---------------------------------------------
000 Return to factory settings with the ex-
ception of the addresses associated with
the call buttons.
001 Return to factory settings of the address-
es associated with the call buttons.
---------------------------------------------
P1
099
P2
100
P3
101
P4
102
P5
103
P6
104
P1
099
P2
100
P5
103
P6
104
P7
105
P8
106