Parts List - Kavan SAVAGE mini Bauanleitung

ASSEMBLY
Follow the illustrated, step-by-step building manual on pages 9-15 please.
RC SET INSTALLATION AND PREFLIGHT CHECK
• Referring to the instruction manual of your radio carefully hook up the on-
-board electronics. Correct linkage length - refer to assembly steps 24, 50 and
60 please.
• Once everything has been correctly connected, turn on your transmitter and
plug in the flight pack. Check the neutral positions and throws of all control
surfaces. If you needed to make the control surface throws smaller, simply
move the pushrod closer to the centre on the servo arm or move it far from the
control surface on the control horn. And vice versa.
Low Rate
Recommen-
ded Throws
Rate
Ailerons ±30°
Elevator ±30°
Rudder ±35°
FLYING
The test flying and fine tuning is pretty much straightforward, there will be
no surprise for a medium-advanced pilot that is supposed to fly this model.

PARTS LIST

If in doubts, the manual step No. will help you identify the part.
Part
Instruction Manual
Fuselage - Vertical Part
Fuselage - Horizontal Part
Wing - Left + Right
Canopy
Fin and Rudder
Horizontal Stabilizer +
Elevator
Wheel Pant
Side Force Generator
Main Undercarriage
Carbon Parts Bundle
Wing Spar
Fuselage Reinforcement
Horizontal Tailplane Reinfor-
cement
Horizontal Tailplane Reinfor-
cement
Elevator + Rudder Push Rod
Small Accessories Bag
Firewall
Wing Joiner
Aileron Push Rod
Aileron, Elevator, Rudder
Horns
Tailskid
Undercarriage Plate
Wheel
Wheel Pant Holder
Wheel Axle
M3 Nut
M3 Washer
Undercarriage Bolt
Undercarriage Bolt Holder
Undercarriage Bracket
Clevis
Clevis Pin
M2 Ball Link
High Rate
Expo Rate
45% ±44° or more
45% ±50-60°
50% ±47°
Qty Material Dimensions
1 paper A4
1 EPP
1 EPP
1+1 EPP
1 EPP
1 EPP
1 EPP
2+2 EPP
2 EPP
1 carbon
2 carbon Ø1.5x1000 mm
4 carbon 3x0.5x1000 mm
2 carbon 3x0.5x250 mm
1 carbon 3x1x250 mm
1 carbon Ø1.0x1000 mm
1 plywood 3 mm
1 plywood 1 mm
2 Ø1.8x110 mm
1 set plastic
1 plastic
1 plastic
2 plastic Ø40 mm
2 plastic
M3x16 mm socket
2 steel
screw
4 steel M3
4 steel
M3x25 mm soc-
4 steel
ket screw
2 plastic
2 plastic
7 plastic
7 brass
plastic/
1
brass
• The „Low Rate" recommended control surface throws are suitable for a less
skilled pilot and classic pattern aerobatics; the „High Rate" setting is for 3D
aerobatics and skilled pilots.
• Check the direction of rotation of the propeller. If it was incorrect, simply
swap two of the tree wires between the ESC and motor or program the ESC
(refer to the ESC manual).
• Attach the flight pack to the side of the bottom part of the fuselage using
a strip of hook-and-loop tape to get the correct position of the centre of
gravity (CG) 230 mm, refer to Fig. 63. You can fine tune the CG position
later in order to suit your flying style.
Expo
• Fully charge your flight pack and transmitter batteries, check the proper
40%
function of your radio and perform the range check of your radio according
45%
to its instruction manual. The range has to be almost the same with the
50% motor off and at full throttle (no more than 10% decrease is acceptable). DO
NOT try to fly unless the range check is 100% successful.
Step
Part
No.
M2/1 Threaded Coupler
28 M2/2 Threaded Coupler
1 Clevis Spacer
2 Push Rod Guide
28 Aileron Servo Arm
56 Motor Mount Screw
9
41
61
32
6
12
9, 10
9
46,
50,
60
53
7
23
21, 45,
57
15
36
36
36
36
36
35
31
32
23,
46,
59
23,
46,
59
51
4
Qty Material Dimensions
2 brass
2 brass
2 plastic Ø2 mm
10 plastic
2 plastic
4 steel Ø2.9x6 mm
Step
No.
48, 51
23
46
43
16
62