Makita CE002G Betriebsanleitung Seite 13

10. Use extra caution when making a "pocket cut"
into existing walls or other blind areas. The
protruding wheel may cut gas or water pipes, elec-
trical wiring or objects that can cause kickback.
Additional Safety Warnings:
1. Do not use abrasive cut-off wheel. Otherwise fire
and/or excessive heating may cause burn injury.
2. Do not cut metal object. Otherwise fire and/or
excessive heating may cause burn injury.
3. Before using a segmented diamond wheel,
make sure that the diamond wheel has the
peripheral gap between segments of 10 mm
(3/8") or less, only with a negative rake angle.
4. Never attempt to cut with the tool held upside
down in a vise. This can lead to serious acci-
dents, because it is extremely dangerous.
5. Some material contains chemicals which may
be toxic. Take caution to prevent dust inhala-
tion and skin contact. Follow material supplier
safety data.
6. Store wheels as per manufacturer recommenda-
tions. Improper storage may damage the wheels.
7. Always use the wheel suitable for your work
and the material to be cut.
8. Examine the material to be cut before cutting.
If the material contains explosive or flammable
substances, it may cause an explosion or fire.
9. Do not switch on the tool if a foreign object
is jammed between the wheel cover and the
wheel. In this case, uninstall the battery cartridge
and remove the foreign object.
10. Use clamps or similar to support the work-
piece whenever possible.
11. Always wear hearing protection during operation.
12. Do not cut wood materials with this tool.
13. The outside diameter and the thickness of the
wheel must be within the capacity rating of
your power tool. Incorrectly sized wheels cannot
be adequately guarded or controlled.
14. When operating the power tool, maintain a firm
grip with both hands on the power tool and
position your body and arm to allow you to
resist kickback forces.
15. Keep your hands or face away from the rotat-
ing wheel.
16. Adjust the wheel cover to a position suitable
for your work.
17. Do not wet the tool with water, rain, mud, and
puddle.
18. Do not leave the tool unattended outdoors.
19. When storing the tool, avoid direct sunlight
and rain, and store it in a place where it does
not get hot or humid.
20. Clean the filter of vacuum cleaner regularly.
SAVE THESE INSTRUCTIONS.
WARNING:
DO NOT let comfort or familiarity
with product (gained from repeated use) replace
strict adherence to safety rules for the subject
product. MISUSE or failure to follow the safety
rules stated in this instruction manual may cause
serious personal injury.
Important safety instructions for
battery cartridge
1. Before using battery cartridge, read all instruc-
tions and cautionary markings on (1) battery
charger, (2) battery, and (3) product using
battery.
Do not disassemble or tamper with the battery
2.
cartridge. It may result in a fire, excessive heat,
or explosion.
If operating time has become excessively
3.
shorter, stop operating immediately. It may
result in a risk of overheating, possible burns
and even an explosion.
If electrolyte gets into your eyes, rinse them
4.
out with clear water and seek medical atten-
tion right away. It may result in loss of your
eyesight.
Do not short the battery cartridge:
5.
(1) Do not touch the terminals with any con-
ductive material.
(2) Avoid storing battery cartridge in a con-
tainer with other metal objects such as
nails, coins, etc.
(3) Do not expose battery cartridge to water
or rain.
A battery short can cause a large current
flow, overheating, possible burns and even a
breakdown.
6. Do not store and use the tool and battery car-
tridge in locations where the temperature may
reach or exceed 50 °C (122 °F).
7. Do not incinerate the battery cartridge even if
it is severely damaged or is completely worn
out. The battery cartridge can explode in a fire.
8. Do not nail, cut, crush, throw, drop the battery
cartridge, or hit against a hard object to the
battery cartridge. Such conduct may result in a
fire, excessive heat, or explosion.
9. Do not use a damaged battery.
10. The contained lithium-ion batteries are subject
to the Dangerous Goods Legislation require-
ments.
For commercial transports e.g. by third parties,
forwarding agents, special requirement on pack-
aging and labeling must be observed.
For preparation of the item being shipped, consult-
ing an expert for hazardous material is required.
Please also observe possibly more detailed
national regulations.
Tape or mask off open contacts and pack up the
battery in such a manner that it cannot move
around in the packaging.
When disposing the battery cartridge, remove
11.
it from the tool and dispose of it in a safe
place. Follow your local regulations relating to
disposal of battery.
12. Use the batteries only with the products
specified by Makita. Installing the batteries to
non-compliant products may result in a fire, exces-
sive heat, explosion, or leak of electrolyte.
13. If the tool is not used for a long period of time,
the battery must be removed from the tool.
13 ENGLISH