Herunterladen Inhalt Inhalt Diese Seite drucken

Initial Operation; Changing The Tool; Maintenance And Cleaning; Depth Stop - Bosch GSR 6-20 TE Bedienungsanleitung

Vorschau ausblenden Andere Handbücher für GSR 6-20 TE:
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 1

Initial Operation

Observe correct mains voltage: The voltage of
the power source must agree with the voltage
specified on the nameplate of the machine.
Equipment marked with 230 V can also be con-
nected to 220 V.
Switching On and Off
To start the machine press the On/Off switch 6.
The machine runs with variable
speed between 0 and maximum,
depending on the pressure applied
to the On/Off switch 6. Light pres-
sure results in a low rotational
speed thus allowing smooth, con-
trolled starts.
Lock the pushed On/Off switch 6 by pressing the
lock-on button 5.
To switch off the machine, release the On/Off
switch 6 or push and release it then.
Reversing the Rotational Direction
Operate
the
switch 7 only at a standstill.
Set rotational direction selector 7 to R (right or
clockwise) or L (left or anticlockwise). (Rotational
direction selector 7 is locked when
switch 6 is activated).

Changing the Tool

To change the screwdriver blade 1, pull off the
depth stop 2 to the front. The preselected screw-
ing depth is altered as a result.

Depth Stop

With the adjustment collar 3, the screwing depth
of the screw head in the material can be prese-
lected in 8 indented steps per revolution (of
0.2 mm each):
Slide the adjustment collar 3 forward to the stop.
Set screwing depth by rotating the adjustment
collar 3:
Clockwise
= Increased screwing depth
Counter-clockwise = Decreased screwing depth
Then slide the adjustment collar 3 backward to
the stop.
The required setting can best be determined by a
trial screw driving.
10 • 3 609 929 623 • TMS • 14.03.03
rotational
direction
On/Off
English - 2
The screw is held by the magnetic universal
holder (Type GSR 6-25 TE / GSR 6-40 TE).
Press the point of the screw firmly against the
material to be screwed until the depth stop 2
rests against the material and the screw driving
insert disengages.
To loosen screws, set the reversing switch 7 to
counter-clockwise and pull off the depth stop 2 to
the front.
Belt clip
With the belt clip 4, the machine can be hung
onto a belt. The user has both hands free and the
machine is always at hand.

Maintenance and Cleaning

Before any work on the machine itself, pull
the mains plug.
For safe and proper working, always keep the
machine and the ventilation slots clean.
If the machine should fail despite the care taken
in manufacturing and testing procedures, repair
should be carried out by an after-sales service
centre for Bosch power tools.
In all correspondence and spare parts orders,
please always include the 10-digit order number
given on the nameplate of the machine.
WARNING! Important instructions for con-
necting a new 3-pin plug to the 2-wire cable.
The wires in the cable are coloured according to
the following code:
strain relief
live = brown
neutral = blue
Do not connect the blue or brown wire to the
earth terminal of the plug.
Important: If for any reason the moulded plug is
removed from the cable of this machine, it must
be disposed of safely.
To be fitted
by qualified
professional only

Quicklinks ausblenden:

Werbung

Inhaltsverzeichnis
loading

Diese Anleitung auch für:

Gsr 6-25 teGsr 6-40 te

Inhaltsverzeichnis