Getting Started; Essential Oils; Replacing The Filter; Cleaning - ProBreeze PB-12 Bedienungsanleitung

GETTING STARTED

― ―
Prior to operating the appliance, the water tank will need to be filled.
To do so:
1. Using the handle remove the water tank from the base of the appliance.
2. Turn the water tank upside down and unscrew the water tank cap. The water tank cap
forms part of the water filter which helps to eliminate contaminants in the water.
3. Fill the water tank with cold or room temperature water (for best results and to prohibit and/
or reduce build up of white dust (limescale) use distilled water). The maximum capacity of
the water tank is 5.6L.
4. Screw the water tank cap tightly back into position to prohibit leaking.
5. Using two hands replace the water tank on the base of the appliance. Be sure to align the
water tank with the base correctly so that it fits securely in place thereby
preventing leaking.
Once the water tank has been filled, to operate the appliance:
1. Plug the power cord into a suitable power socket.
2. Press the power button to turn the appliance on.
3. After a few seconds mist will start to flow out of the mist outlet.
4. Choose the desired settings.
5. Adjust the 360° mist outlet by hand to direct the mist flow.
Note: When the humidifier is low on water a beep will sound and a red low water level indicator
light will illuminate on the LED display.

ESSENTIAL OILS

― ―
The aroma diffuser pod allows you to use essential oils to generate a scented mist.
To use:
1. Remove the 360° mist outlet by lining up the two small arrows and lifting up.
2. Open the lid of the aroma diffuser pod and place two to three drops of your chosen essential
oil on the aroma diffuser pad.
3. Close the aroma diffuser pod and replace the 360° mist outlet locking it into position by
ensuring that the two arrows are not aligned.
4. Operate the appliance as normal but now with a scented mist.
Note: The aroma diffuser pad should only be used for one essential oil. Prior to using a
different essential oil clean the aroma pad by lightly hand washing it in warm water and
then leaving to air dry. Spare aroma diffuser pads are included for your convenience.
10 of 76 | English

REPLACING THE FILTER

― ―
The ion-exchange resin filter is designed to remove impurities from the water and ensure
it stays clean for as long as possible. We recommend replacing your filter at least once
every three months or 700 hours of use.
To replace the filter:
1. Turn off the appliance and unplug it from the power socket.
2. Using the handle remove the water tank from the base of the appliance.
3. Turn the water tank upside down and unscrew the water tank cap.
4. Unscrew the filter from the water filter cap and replace with a new filter.
5. Screw the water tank cap tightly back into position to prohibit leaking.
Notes: Do not throw the water filter cap away when replacing the filter. The water reservoir will
have filled with water during the operation of the appliance. This is normal and is required for the
appliance to operate as a humidifier.
Replacement filter model number: PB-12F

CLEANING

― ―
This appliance requires regular cleaning to reduce the risk of bacteria growth and to remove any
limescale residue. We recommend cleaning the appliance once a week if being used daily.
To clean the appliance:
1. Turn off the appliance and unplug it from the power socket.
2. To clean the pre-filter, remove the pre-filter from the bottom of the appliance and tap to
remove any debris. Replace once clean.
3. To clean the water tank, using the handle remove the water tank from the base of the
appliance.
4. Turn the water tank upside down and unscrew the water tank cap.
5. Unscrew the filter from the water filter cap and place to one side.
6. Fill the water tank with two tablespoons of distilled vinegar or bleach in 3L of water and let it
stand for 20 minutes.
7. Screw the water tank cap (without the filter attached) back tightly into position and shake
well for a few minutes.
8. Unscrew the water tank cap and screw the filter back into position. Drain and rinse the water
tank with clean water until the distilled vinegar or bleach smell has gone. Then dry with a
clean, soft cloth.
9. To clean the base, fill the base with water and two teaspoons of distilled vinegar or bleach
and soak for 20 minutes. Drain the base and rinse with clean water. Then dry with a clean,
soft cloth. Do not immerse the base in water.
10. Use the cleaning brush housed in the bottom of the water tank to gently clean the ultrasonic
oscillator of any white dust (limescale) or debris build up. Note: Use distilled water to
English | 11 of 76