Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
NORSUP CARTRIDGEFILTER
3.
STARTING THE PUMP AND FILTER SYSTEM
3.1
BEFORE STARTING THE PUMP
ARTING THE PUMP AND FILTER SYSTEM
1. Use ONLY CF system components, Locking Ring
TARTING THE PUMP AND FILTER SYSTEM
unit doing assembly, metal-reinforced seal. Non-
tighten locking ring components may fail in use
and cause explosive component separation. Verify
ORE STARTING THE PUMP
that upper and lower filter bodies are properly
EFORE STARTING THE PUMP
secured with the filter body locking ring unit. Make
CF system components, Locking Ring unit doing assembly, metal-reinforced seal. Non-tighten locking
sure hand tightening enough the locking Ring
NLY CF system components, Locking Ring unit doing assembly, metal-reinforced seal. Non-tighten locking
enough to the filter upper and bottom body. Verify
ponents may fail in use and cause explosive component separation. Verify that upper and lower filter
omponents may fail in use and cause explosive component separation. Verify that upper and lower filter
that the filter manual air release valve is in the LOCK
e properly secured with the filter body locking ring unit. Make sure hand tightening enough the locking
position, and no filter components are missing,
s are properly secured with the filter body locking ring unit. Make sure hand tightening enough the locking
ugh to the filter upper and bottom body. Verify that the filter manual air release valve is in the LOCK
damaged, or not genuine ICF filter components.
enough to the filter upper and bottom body. Verify that the filter manual air release valve is in the LOCK
and no filter components are missing, damaged, or not genuine ICF filter components.
on, and no filter components are missing, damaged, or not genuine ICF filter components.
Upper body
Upper body
Clamp bolt
Clamp bolt
Bottom base
Locking clamp
Bottom base
Locking clamp
Figure 1
Figure 1
r drain. Note: Filter plug requires an O ring seal.
2. Close filter drain. Note: Filter plug requires an
filter drain. Note: Filter plug requires an O ring seal.
O ring seal.
Sealing O ring
Sealing O ring
Drain Plug
Drain Plug
Figure 2
Figure 2
ystem valves to allow water from the pool to the filtration system and from the filter to return to the
all system valves to allow water from the pool to the filtration system and from the filter to return to the
manual air release valve in an OPEN position.
3. Open all system valves to allow water from the pool
the manual air release valve in an OPEN position.
to the filtration system and from the filter to return
Relief valve
to the pool.
Release direction
Release direction
Figure 3
10
WWW.NORSUP.EU
Figure 3
Sealing O ring
Drain Plug
Figure 2
Open all system valves to allow water from the pool to the filtration system and from the filter to return to the
3.
pool.
4. Place the manual air release valve in an OPEN
position.
Place the manual air release valve in an OPEN position.
4.
3.2 STARTING PUMP
Stand clear of pump during start-up
Release direction
When starting the system pump, do not stand over or near the filter. If water leakage appears at the filter tank clamp,
1.
immediately turn off all system circulation pumps and all electrical power. Do not return to the filter until all water
leakage has stopped. Reassemble the clamp system per the instructions of the previous page in this owner 's manual
to stop the leak.
Figure 3
Return to the filter and only CLOSE the manual air relief valve if a steady stream of water escapes from the valve and
2.
not air or an air-water mix.
3.2
STARTING PUMP
P6
STARTING THE PUMP AND FILTER SYSTEM
Stand clear of pump during start-up
Clamp nut
Clamp nut
3.3 OPERATION
Filtration starts as soon as the flow is steady through the filter. As
the filter removes dirt from the pool water, the accumulated dirt
causes a resistance to flow. As a result, the gauge pressure will
Pool and spa circulation systems operate under high
rise, and the flow will decrease. When the pressure rises to 30 psi
pressure. When any part of the circulating system
(200 kPa) above the starting pressure, or when the flow decreases
(i.e., lock ring, pump, filter, valves, etc.) is ser viced,
below the desired rate, clean or replace the filter cartridge
air can enter the system and become pressurized.
elements.
Filter tank Lid and pre- filter cover must be properly
secured to prevent violent separation. Place pre-filter /
Once your filter is running and there is a pressure reading, turn
filter air relief valve in the open position and wait for
the outer dial "START" arrow marker to the pressure gauge pointer
all pressure in the system to be relieved before remove
position. When the pressure rises to or above the "CLEAN FILTER"
the lib to access the basket for cleaning.
marker, it is time to clean or replace your filter cartridge elements.
1. When starting the system pump, do not stand over
By recording the initial starting pressure (with clean filter
or near the filter. If water leakage appears at the filter
elements) a determination can be made when the filter cartridge
tank clamp, immediately turn off all system circulation
elements should be replaced rather than cleaned.
pumps and all electrical power. Do not return to the
After the filter elements have been cleaned and reinstalled if
filter until all water leakage has stopped.
the starting pressure is higher than 25 PSI above the starting pressure with the new filter cartridge elements, the filter
Reassemble the clamp system per the instructions
cartridge elements should be replaced the next time the gauge arrow reaches the red zone.
of the previous page in this owner 's manual to
stop the leak.
2. Return to the filter and only CLOSE the manual air
relief valve if a steady stream of water escapes from
4.
MAINTAINING YOUR FILTER
the valve and not air or an air-water mix.
Relief valve
This product should be installed and ser viced only by a qualified pool professional.
Alterations which serve the technological progress as well as errors excepted!
NORSUP CARTRIDGEFILTER
3.3
OPERATION
Filtration starts as soon as the flow is steady through
the filter. As the filter removes dirt from the pool water,
the accumulated dirt causes a resistance to flow. As
Relief valve
a result, the gauge pressure will rise, and the flow will
decrease. When the pressure rises to 30 psi (200 kPa)
above the starting pressure, or when the flow decreases
Pool and spa circulation systems operate under high pressure. When any part of
below the desired rate, clean or replace the filter
the circulating system (i.e., lock ring, pump, filter, valves, etc.) is ser viced, air
cartridge elements.
can enter the system and become pressurized. Filter tank Lid and pre- filter
cover must be properly secured to prevent violent separation. Place pre-filter /
Once your filter is running and there is a pressure
filter air relief valve in the open position and wait for all pressure in the system
reading, turn the outer dial "START" arrow marker
to be relieved before remove the lib to access the basket for cleaning.
to the pressure gauge pointer position. When the
pressure rises to or above the "CLEAN FILTER" marker,
it is time to clean or replace your filter cartridge
elements.
By recording the initial starting pressure (with clean
filter elements) a determination can be made when
the filter cartridge elements should be replaced
rather than cleaned. After the filter elements have
been cleaned and reinstalled if the starting pressure
is higher than 25 PSI above the starting pressure with
the new filter cartridge elements, the filter cartridge
elements should be replaced the next time the gauge
arrow reaches the red zone.
4.
MAINTAINING YOUR FILTER
This product should be installed and ser viced only
by a qualified pool professional.
4.1
FILTER DISASSEMBLY INSTRUCTION
1. Turn off all system circulation pumps and all-electric
power on the equipment pad.
2. Set all system valves in a position to prevent water
flow to the filter.
3. The manual air release valve must be placed in the
OPEN position. 4.Remove the filter drain plug and
drain water from the filter.
5. Holding locking Ring Unit of the filter clamp carefully
as, lifting through top filter body. Do not drop the
locking ring unit during removal, because the locking
ring unit could be damaged. Do not strike the locking
P7
MAINTAINING YOUR FILTER
Alterations which serve the technological progress as well as errors excepted!
all system valves in a position to prevent water flow to the filter.
3.The manual air release valve must be placed in the OPEN position.
4.Remove the filter drain plug and drain water from the filter.
Holding locking Ring Unit of the filter clamp carefully as, lifting through top filte
5.
ring unit during removal, because the locking ring unit could be damaged. Do
with metal tools as they can damage the clamp.
Lift off upper filter body. Do not use the pressure gauge to lift the upper filter bod
6.
Ring unit with metal tools as they can damage the
4.2 REMOVING CARTRIDGES
clamp.
6. Lift off upper filter body. Do not use the pressure
gauge to lift the upper filter body.
1.Remove the filter cartridge elements by using a slight rocking motion and lifting.
2.Clean filter cartridge elements.
4.2 REMOVING CARTRIDGES
1. Remove the filter cartridge elements by using
a slight rocking motion and lifting.
2. Clean filter cartridge elements.
4.3 CLEANING CARTRIDGES
4.3 CLEANING CARTRIDGES
The Cartridge filter element can be cleaned by washing
inside and outside with a garden hose. After hosing
The Cartridge filter element can be cleaned by washing inside and outside with
the cartridge, for best results, carefully brush the
cartridge, for best results, carefully brush the pleated surface to remove fine partic
pleated surface to remove fine particles. Do not
pressure wash as it can damage the filter element.
can damage the filter element.
You may find some debris on the cartridge pleats,
You may find some debris on the cartridge pleats, which may not have been removed w
which may not have been removed with hosing
Sealing O ring
Bottom base
Sealing surface
4.4 FILTER REASSEMBLY INSTRUCTION
4.4 FILTER REASSEMBLY INSTRUCTION
4.4.1 RE-INSTALLATION CARTRIDGES
1. Flush and drain any dirt or debris from the bottom
4.4.1 RE-INSTALLATION CARTRIDGES
of the lower filter body.
2. Flush any dirt or debris from the upper filter body
Figure 4
and from around the manual air release area.
Flush and drain any dirt or debris from the bottom of the lower filter body.
1.
3. Carefully replace the cartridges over the hubs
Flush any dirt or debris from the upper filter body and from around the manual a
2.
on the bottom manifold.
3.Carefully replace the cartridges over the hubs on the bottom manifold.
4. Place top filter body securely on top of cartridges.
4.Place top filter body securely on top of cartridges.
4.4.2
CLEAN SEAL RING AND SEAL SURFACE
1. Remove filter tank sealing O Ring.
2. With a clean cloth, wipe the lower filter body
4.4.2 CLEAN SEAL RING AND SEAL SURFACE
seal surface and clean seal of all dirt and debris.
Do not use a solvent.
3. With a clean cloth wipe the upper filter body
Remove filter tank sealing O Ring.
1.
seal surface.
With a clean cloth, wipe the lower filter body seal surface and clean seal of all dir
2.
NOTICE
solvent.
With a clean cloth wipe the upper filter body seal surface.
3.
Do not use any petroleum solvents to clean filter
components Do not lubricate sealing O ring. If
the O ring is damaged, it must be replaced
EN
EN
DE
DE
FR
FR
NL
DK
Top Closure Plate
SE
Figure 5
P8
MAINTAINING YOUR FILTER
ORIGINAL MANUAL NORSUP
11
Werbung
Inhaltsverzeichnis
Fehlerbehebung
