Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
EN
1 Important safety instructions
Caution
•
Read these instructions before you begin. If you are unsure of any
part of the process, contact a professional contractor or installer
for assistance. Improper installation can result in injury or damage,
•
The wall or mounting surface must be capable of supporting
the combined weight of the mount and the display, if not the
structure must be reinforced.
•
Locate pipes, wires, or any other hazards in the wall where you
wish to install the mount before drilling.
•
Three people are recommended for installation. Do not attempt
to lift a heavy display without assistance.
•
This wall mount is intended for use only with the maximum
weight of 35 kg (77 lbs). Use with heavier than the maximum
weights indicated may result in instability causing possible injury
2 Full motion wall mount (for LCD, Plasma, and
LED displays)
What's in the box
Full motion mount (×1)
Adapter (×4)
Hardware kit
Drywall screws (×3)
A
Concrete anchor (×3)
B
Washers (×7)
C
M6×10 (×8)
D
M6 lock nut (×8)
E
M5×20 (×4)
F
Tools required
•
Phillips head screw driver
•
Electric or portable drill
•
•
8 mm (5/16") Masonry bit for concrete installation
•
Level
Preparation
•
Prepare the mount for installation by
disassembling the display plate from
the mount. Do this by removing the
safety screws as shown .Place the
screws in a safe location.
3 Installation
Mount to the drywall
Caution
For safety reasons, this mount must be secured to a wood stud of
supporting the combined weight of the mount and display Do not
mount to drywall alone.
1
install your mount. Mark both edges of each stud to help identify
the exact center.
2 Place the mount against the wall over the marked stud. Make
sure it is level and right side up.
User manual (×1)
Hardware kit (×l)
M6x20 (×4)
G
M8x30 (×4)
H
Spacer (×4)
I
Spirit bubble (×1)
J
Wrench (×1)
3 Mark three Locations vertically at the center of the stud for
securing the mount to the wall (see Fig. 1) and set it aside.
4 Drill a 50 mm pilot hole at each marked location.
5 Place the mount back against the wall and attach it using the
drywall screws (A) and three of the washers (C) provided (see
Fig. 2). Do not over-tighten these screws . Ensure that the mount
remains level after all screws are secured.
Mount to the concrete wall
Caution
For safety reasons, the concrete wall must be capable of supporting
the combing weight of the mount and the display. The manufacturer
1 Place the mount against the wall in the desired location and
make sure it is level and right side up.
2 Mark three lotions vertically at the center of the stud for securing
the mount to the wall (see Fig.1) and set it aside.
3 Drill 50mm pilot hole at each marked location.
Remove any excess dust from the holes.
Insert a concrete anchor (B) into each hole so that it is flush
4
with the concrete surface (see Fig. 2). A hammer can be used to
lightly tap the anchors into place if necessary.
Note
If the concrete wall is covered by a layer of plaster or dry wall, the
concrete anchor must pass completely through the layer to rest
5 Place the mount back against the wall and attach it using the
drywall screws (A) and three of the washers (C) provided (see
Fig. 3). Do not over-tighten these screws . Ensure that the mount
remains level after both screws are secured.
Attaching the display plate to the display
Caution
Use extra care during this part of the installation. If possible, avoid
facing down your display as it may damage the viewing surface.
Note
This mount comes with a selection of different screws to
accommodate a wide variety of display models. Not all of the
screw size in the kit provided, consult the manufacturer of your
display for more information.
1 Examine the mounting holes on the back of your display:
•
If the mounting holes are spaced 75 mm × 75 mm or 100 mm ×
100 mm apart, skip this section and proceed with step 3.
•
If the mounting holes are spaced 100 mm × 200 mm or
200 mm × 200 mm or 300 mm × 300 mm or 400 mm × 400
mm apart you will need to use the adapters included with
your mount Attach these to the mount according to the
illustration (see Fig. 4). Use the M6 × 10 screws (D), M6 lock
nuts (E) and wrench (J) from the hardware kit.
1
Werbung
Inhaltsverzeichnis
