Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
OPERATION
Charging the battery pack （Fig. J）
NOTE: Remove the battery pack from the charger after it has been fully charged.
NOTE: Battery should be fully charged before first use.
NOTE: Make sure the mains voltage is the same as rating label which is located on the
charger.
1.
Connect the charger to a power supply. The red LED will light up.
2.
To insert the battery pack into the charger, align the raised ribs of the battery pack with
the grooves of the charger then push it in. (Fig. J)
3.
The green LED light of the charger will flash continuously during normal charging.
4.
After charging is complete, the green LED will light up.
Power indicator (Fig. K)
This Li-Ion battery pack is equipped with a power indicator which is used to show the battery
pack's remaining charge. Press the power indicator button to check battery charge as below.
The LEDs will stay lit for approximately 4 seconds.
To obtain the best life from the battery
1.
Never allow the battery to completely discharge before recharging. The battery pack
should be placed on the charger whenever the battery pack is noticeably running down
or the tool no longer performs a task it previously performed.
2.
Avoid conducting short charges. Make sure that the battery is fully charged each time by
allowing the charger to complete its full charging cycle.
3.
Avoid allowing loose items like screws or nails etc. to be stored with battery packs as
these or similar items can short battery packs and cause a fire or explosion
4.
Always unplug the charger when not in use and store in a dry and secure place.
5.
Avoid charging or storing your battery in temperatures below 5°C and above 45°C.
6.
After use, allow the battery to pack to cool down for approximately 30 minutes before
attempting to recharge.
Removing and inserting the battery pack
Insert the battery pack. (Fig. M)
Align the battery pack with its compartment of the tool. Push the battery pack into the tank
until you hear a click. This means the battery pack has been locked in position, then close the
battery pack tank cover.
Removing the battery pack from the tool (Fig. N)
Open the battery pack tank cover. Push the battery pack release button, the battery pack will
come out automatically.
NOTE: Safety-Key (Fig. O)
This lawnmower is fitted with a safety key; this prevents the accidental start up of your
cordless lawnmower.
The safety key has been designed to totally disable the lawnmower when it is removed.
24
OPERATION
Setting cutting height (Fig. L)
If you wish to change the cutting height, push the adjusting lever first to make it out of the
tooth and then push the lever to the desired position.
WARNING: Never operate the adjusting handle roughly.
Switching on and off (Fig. P)
Switch on:
1. Press and hold the safety button on the side of the switch box with one hand.
2. Pull the switch bar towards the handle and hold it with the other hand.
Switch off:
Release the switch bar.
NOTE: Do not continue to press the start button after an automatic shut-off of the machine,
this will lead to battery damage.
WARNING:
When the motor has been switched off, the blade will continue to run for several seconds. Do
not touch the underside of the mower until the cutter has come to a complete standstill!
Operating the lawnmower
Operation on a slope:
Slopes increase the risk of slip-and-fall accidents, which can result in severe injury. Always be
sure of your footing on slopes. Operation on slopes requires extra caution. If you feel uneasy
on a slope, do not mow it.
Do:
- Mow across the face of slopes, never mow up and down. Exercise extreme caution when
changing direction on slopes.
- Watch for holes, ruts, rocks, hidden objects or bumps which could cause you to slip or
trip. Tall grass can hide obstacles.
Do not:
- Do not mow near drop-offs, ditches or embankments; you could lose your footing or
balance.
- Do not mow slopes greater than 15 degrees.
- Do not mow on wet grass. Unstable footing could cause you to slip.
Mower overload protection
To prevent overload conditions, do not try to cut too much grass at one time. Slow down your
cutting pace or raise the cut height. Your mower has built-in overload circuit protection. When
25
Werbung
Inhaltsverzeichnis
