Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Operating Instructions
SPS5-12W-N SWITCHED-MODE
POWER SUPPLY
Item No. 2266527
Intended Use
The product serves as voltage supply for low-voltage devices with matching DC jacks and for
USB devices. It is intended for connection to common household mains voltage (100 - 240 V/
AC, 50/60 Hz). The power consumption of the consuming device may not exceed the nominal
voltage of the product. The product has a protection against short circuit and overload.
This product fulfils European and national requirements related to electromagnetic compatibil-
ity (EMC). CE conformity has been verified and the relevant statements and documents have
been deposited at the manufacturer.
It is intended for indoor use only. Do not use it outdoors. Contact with moisture, e.g. in bath-
rooms, must be avoided under all circumstances.
For safety and approval purposes, you must not rebuild and/or modify this product. If you use
the product for purposes other than those described above, the product may be damaged. In
addition, improper use can result in short circuits, fires, electric shocks or other hazards. Read
the instructions carefully and store them in a safe place. Make this product available to third
parties only together with its operating instructions.
This product complies with the statutory national and European requirements. All company
names and product names are trademarks of their respective owners. All rights reserved.
Delivery Content
• Power supply
• 8 x adaptor plugs
• Operating instructions
Up-to-date Operating Instructions
Download the latest operating instructions at www.conrad.com/downloads or
scan the QR code shown. Follow the instructions on the website.
Explanation of Symbols
The symbol with the lightning in the triangle is used if there is a risk to your health,
e.g. due to an electric shock.
The symbol with the exclamation mark in the triangle is used to indicate important
information in these operating instructions. Always read this information carefully.
The arrow symbol indicates special information and advice on operation.
This product must only be used in dry, enclosed indoor areas. It must not become
damp or wet, as this may result in a fatal electric shock!
Protection class 2 (double or reinforced insulation, protective insulation).
This symbol indicates that the product meets the energy efficiency requirements for
Class VI.
Safety Instructions
Read the operating instructions carefully and especially observe the safety
information. If you do not follow the safety instructions and information on
proper handling in this manual, we assume no liability for any resulting per-
sonal injury or damage to property. Such cases will invalidate the warranty/
guarantee.
a) General Information
• The device is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. This may become dan-
gerous playing material for children.
• Protect the appliance from extreme temperatures, direct sunlight, strong jolts, high
humidity, moisture, flammable gases, steam and solvents.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, take it out of operation and
protect it from any accidental use. Safe operation can no longer be guaranteed
if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions or
- has been subjected to any serious transport-related stresses.
• Please handle the product carefully. Jolts, impacts or a fall even from a low height
can damage the product.
• Never touch the device with wet or moist hands. There is a danger of electrocu-
tion.
• On commercial premises, the accident prevention regulations of the relevant pro-
fessional insurance association for electrical systems and operating materials are
to be observed.
• Operation in unfavourable ambient conditions is not permitted. Adverse ambient
conditions are:
- moisture or excessive humidity
- dust and combustible gases, vapours or solvents
• Since the device generates heat when operating, ensure that it is adequately ven-
tilated. The housing must not be covered!
• Never switch the device on immediately after having taken it from a cold to a warm
environment. Under adverse conditions, the resulting condensation could destroy
the device. Allow the device to reach room temperature before switching it on.
• Power units are not designed for application to human beings or animals.
• Consult an expert when in doubt about the operation, safety or connection of the
appliance.
• Maintenance, modifications and repairs must only be completed by a technician
or an authorised repair centre.
• If you have questions which remain unanswered by these operating instructions,
contact our technical support service or other technical personnel.
b) Connected devices
• Also observe the safety and operating instructions of any other devices which are
connected to the product.
Operation
The surface of the casing will heat up intensely during prolonged operation at a rated
load. Attention: Danger of burns ! Therefore, take great care to sufficiently ventilate
the power supply unit. Never operate it when partially or fully covered. This will help
avoid any damage.
When connecting a load always take care not to connect it as long as it is switched
on. A load in an ON condition, when being connected to the output terminals of the
power supply unit, can cause sparks to form on the supply terminals. This, in turn,
can damage the supply jacks or the cables connected and/or their terminals.
If you do not need the plug-in mains adapter disconnect it from the mains.
• Select one of the eight adaptor plugs which fits the consumer load at hand.
• Connect the plug to the connector at the end of the output cable. Voltage reversal of the
output plug is not possible for security reasons. The inner contact is positive (+), the outer
negative (–).
Disconnect the power supply unit from the mains socket before replacing the low-
voltage plug.
• Connect the plug to the switched-off consumer.
• Connect the power supply to a standard mains socket.
• Now switch the connected consumer on. If it does not function properly, switch it off im-
mediately and disconnect it from the power supply unit.
• To remove the consumer, proceed in reverse sequence.
• Remove the power supply unit from the mains when it is no longer in use.
Troubleshooting
Problem
Cause
No mains voltage.
Connected loads do not
function.
Power supply overloaded.
Care and Cleaning
• Disconnect the product from the mains before each cleaning.
• Do not use any aggressive cleaning agents, rubbing alcohol or other chemical solutions as
they can cause damage to the housing and malfunctioning.
• Clean the product with a dry, fibre-free cloth.
Solution
Check the circuit breaker of the
power outlet.
Check the correct fit of the power
outlet.
Remove the consumer and check
the technical data.
Werbung
Inhaltsverzeichnis
