Husqvarna PW 240 Bedienungsanweisung Seite 17

CAUTION:
hose without a filter.
4. Push the tab in the direction of the quick connection
on the spray handle and pull out the high-pressure
water hose. (Fig. 25)
5. Connect the power plug to a power source.
6. Turn the power switch to the on (I) position and let
the product operate for 2 minutes.
7. Turn the power switch to the off (0) position.
8. Hold the spray handle tightly with one hand and
push the high-pressure hose into the quick coupling
on the spray handle. (Fig. 24)
9. Bleed the system before you operate the product.
To bleed the system on page 17 .
Refer to
To bleed the system
CAUTION:
switch is in the off (0) position before you
bleed the system.
1. Connect the product to a water source. Refer to
connect the product to a water source on page 16 .
2. Install the spray lance on the spray gun. Refer to
install the spray lance on page 15 .
3. Disengage the power trigger lockout. Refer to
engage and disengage the power trigger lockout on
page 17 .
4. Push the power trigger and keep it pushed in until
water comes out of the nozzle on the spray lance.
(Fig. 40)
To disconnect the product from the water
source
1. Turn the power switch to the off (0) position.
2. If the product is connected to the water mains, close
the valve on the water mains.
3. If the product is connected to the water mains,
disconnect the garden hose from the water mains.
(Fig. 41)
4. If the product is connected to an open water source,
remove the suction hose from the water source.
5. Push the power trigger and keep it pushed in until no
water comes out of the nozzle.
6. Disconnect the garden hose from the water inlet on
the product. (Fig. 42)
Note:
If the product is connected to an open water
source, disconnect the suction hose.
7. Push the tab in the direction of the quick connection
on the spray handle and pull out the high-pressure
water hose. (Fig. 25)
1855 - 006 - 21.10.2022
Do not use a suction
Make sure that the power
To
8. Turn the power switch to the on (I) position. Let the
product operate until no water comes out of the high-
pressure hose.
9. Turn the power switch to the off (0) position.
10. Let the spray handle, the spray lance, and the
nozzles become dry before you put the product in
storage.
To engage and disengage the power
trigger lockout
• To engage the power trigger lockout, push the button
to the locked position. (Fig. 43)
• To disengage the power trigger lockout, push the
button to the unlocked position.
To start the product
1. Connect the product to a water source. Refer to
connect the product to a water source on page 16 .
2. Connect the power plug to a power source.
3. Turn the power switch to the on (I) position. (Fig. 44)
4. Disengage the power trigger lockout. Refer to
engage and disengage the power trigger lockout on
To
page 17 .
5. Push the power trigger on the spray handle.
To
Note:
The product stops automatically when you
release the power trigger.
To stop the product
Note:
The product stops automatically when you
release the power trigger.
1. Release the power trigger on the spray handle.
2. Engage the power trigger lockout. Refer to
engage and disengage the power trigger lockout on
page 17 .
3. Turn the power switch to the off (0) position. (Fig. 45)
4. Disconnect the power plug from the power source.
5. Disconnect the product from the water source. Refer
To disconnect the product from the water source
to
on page 17 .
Note:
Always disconnect the product from the
water source if you go away from the product for
more than 5 minutes.
To use the foam sprayer
1. Remove the foam sprayer from its holder. (Fig. 46)
2. Fill the container on the foam sprayer with cleaning
agent.
To
To
To
17