Werbung
Verfügbare Sprachen
Verfügbare Sprachen
USER MANUAL
EN
Thank you for purchasing this speaker for wall mounting. The speaker is
especially designed for applications in PA systems operating with 100 V
technology. The speaker is protected against dust and water jets and thus can be
used in outdoor areas. The connection must be made by skilled personnel only.
Please read these operating instructions carefully before using the product. They
contain important information for the correct use of your product. Please keep
them for future reference.
SAFETY INSTRUCTIONS
Only use the product according to the instructions given herein. Damages due
Ÿ
to failure to follow these operating instructions will void the warranty! We do not
assume any liability for any resulting damage.
We do not assume any liability for material and personal damage caused by
Ÿ
improper use or non-compliance with the safety instructions. In such cases,
the warranty/guarantee will be null and void.
Unauthorized rebuilds or modifications of the product are not permitted for
Ÿ
reasons of safety and render the warranty invalid.
This product is not a toy. Keep it out of the reach of children. Do not leave
Ÿ
packaging material lying around carelessly.
This product is in accordance with protection grade IP56 and can be used in
Ÿ
outdoor areas. However, do not immerse the product in water, this will destroy
it.
Protect the product against excessive humidity and heat. The recommended
Ÿ
temperature is -5 to +45°C.
Speaker cables are sensitive to electrical interference. Hence, it is
Ÿ
recommended to lay them at a distance of several meters to sources of
interference (e.g. dimmers, light switches).
Make sure that the product is installed securely and cannot fall down. Serious
Ÿ
injury to persons can be caused if the speakers fall down. Comply with the
standards and rules that apply in your country.
For commercial use the country-specific accident prevention regulations of the
Ÿ
government safety organization for electrical facilities must be complied with at
all times.
Make sure that impedance and power rating specified in the technical data
Ÿ
match the connected amplifier's data. Otherwise, the speakers or the amplifier
may be damaged. The total impedance for the connected speakers must not be
less than the minimum impedance for the amplifier.
This product is maintenance-free, except for occasional cleaning. You can use
Ÿ
a slightly dampened cloth for cleaning.
Never open the product. If this product is no longer working properly or is
Ÿ
visibly damaged, take it out of operation and consult your local dealer. Do not
attempt to repair the product yourself.
PROTECTING THE ENVIRONMENT
When to be definitively put out of operation, take the product to a local
recycling plant for a disposal which is not harmful to the environment.
Devices marked with this symbol must not be disposed of as household
waste. Contact your retailer or local authorities for more information.
www.omnitronic.de
© 2022 Omnitronic. All rights reserved • Omnitronic is a brand of Steinigke Showtechnic GmbH • Andreas-Bauer-Str. 5 • 97297 Waldbüttelbrunn, Germany
ODX-212TM
WEATHER-PROOF WALL SPEAKER 100V
ELECTRICAL CONNECTION
During operation, there is a hazard of contact with a voltage of up to 100 V at the
connection wires. The installation must be carried out by skilled personnel only.
Always insulate the connection cables which are not used. Observe the load of
the PA amplifier by the speakers. An overload may damage the amplifier! The total
power of all speakers connected must not exceed the amplifier power.
Mount the speaker to the wall using the supplied bracket.
Ÿ
Turn off the amplifier before making any connection.
Ÿ
Unscrew the cover with the cable inlets on the rear to access the connections.
Ÿ
Connect the speaker via the INPUT terminals to the 100 V output of the PA
Ÿ
amplifier using the correct polarity. The OUTPUT terminals provide the input
signal feed-through for connecting a further speaker system.
Alternatively it is possible to connect the speaker to a low-impedance amplifier
Ÿ
output.
When connecting several speakers, make sure that all speakers have the same
Ÿ
polarity and that the amplifier is not overloaded.
Adjust the rotary switch to the desired power rating for the 100 V operation or
Ÿ
select the 8 Ω position, for directly operating the speaker at a low-impedance
amplifier output.
Fasten the cover on the rear with the screws. Use the nut of the cable inlet to
Ÿ
secure the speaker cable.
TECHNICAL SPECIFICATIONS
Item number: .............................11036965
Input: ........................................100 V or 16 ohms
Protection grade: .......................IP56
Components:.............................30 cm woofer (12"), 4 cm tweeter (1.7")
Connection: ..............................screw terminals
Rated power: .............................100 V: 50/100/200 W RMS
.................................................8 ohms: 300 W RMS
Sensitivity: ................................98 dB
Maximum SPL: ..........................123 dB continuous, 129 dB peak
Frequency range: .......................55-18000 Hz
Dispersion angle: .......................70° x 50°
Crossover: ................................2 kHz
Dimensions (
W x H x D
): .............407 x 410 x 383 mm
Weight:......................................19.7 kg
Subject to change.
Publ. 02/2023
Werbung
