Warranty; Technical Data; Eu Declaration Of Conformity - Kärcher PGS 4-18 Originalbetriebsanleitung

Fault
The device stops during
operation
Saw blade cannot be fit-
ted or removed

Warranty

The warranty conditions issued by our relevant sales
company apply in all countries. We shall remedy possi-
ble malfunctions on your appliance within the warranty
period free of cost, provided that a material or manufac-
turing defect is the cause. In a warranty case, please
contact your dealer (with the purchase receipt) or the
next authorised customer service site.
(See overleaf for the address)

Technical data

Device performance data
Nominal voltage
Stroke rate
Stroke length
Cut material diameter (max.) 
Without branch bow
Cut material diameter (max.) 
With branch bow
Dimensions and weights
Weight (without battery pack)
Length x width x height
Subject to technical modifications.
Vibration value
WARNING
The specified vibration value was measured using a
standard test procedure and may be used to compare
devices.
The specified vibration value may be used in a provi-
sional assessment of the load.
Depending on the way the device is used, the vibration
emission can deviate from the specified overall value
during the current use of the device.
Determine self-protection measures based on an as-
sessment of the load under the actual operating condi-
tions. Take all parts of the operation cycle into account,
for example, the operating time as well as times when
the device is switched off and is out of operation.

EU Declaration of Conformity

EU Declaration of Conformity
We hereby declare that the machine described below
complies with the relevant basic safety and health re-
quirements in the EU Directives, both in its basic design
and construction as well as in the version placed in cir-
culation by us. This declaration is invalidated by any
changes made to the machine that are not approved by
us.
Product: Battery-powered telescopic saw
Cause
Motor has overheated
The battery pack is discharged.
Saw blade tensioner is not in correct po-
sition
PGS 4-
18
V 18
/min 0-2500
mm 20
mm 80
mm 50
kg 1,4
mm 475 x 89
x 174
Rectification
 Stop working and allow the motor to cool
down.
 Charge the battery pack.
 Bring the saw blade tensioner into the cor-
rect position.
Type: PGS 4-18
Currently applicable EU Directives
2006/42/EC (+2009/127/EC)
2014/30/EU
2011/65/EU
Harmonised standards used
EN 55014-1: 2017 + A11: 2020
EN 55014-2: 1997 + A1: 2001 + A2: 2008
EN 62841-1: 2015 + AC: 2015
EN 62841-2-11: 2016 + A1: 2020
EN ISO 11680-1:2011
EN IEC 63000: 2018
The signatories act on behalf of and with the authority of
the company management.
Documentation supervisor:
S. Reiser
Alfred Kärcher SE & Co. KG
Alfred-Kärcher-Str. 28 - 40
71364 Winnenden (Germany)
Ph.: +49 7195 14-0
Fax: +49 7195 14-2212
Winnenden, 2022/10/01
Declaration of Conformity (UK)
We hereby declare that the product described below
complies with the relevant provisions of the following
UK Regulations, both in its basic design and construc-
tion as well as in the version put into circulation by us.
This declaration shall cease to be valid if the product is
modified without our prior approval.
Product: Battery-powered telescopic saw
Type: PGS 4-18
Currently applicable UK Regulations
S.I. 2008/1597 (as amended)
S.I. 2016/1091 (as amended)
S.I. 2012/3032 (as amended)
Designated standards used
EN 55014-1: 2017 + A11: 2020
EN 55014-2: 1997 + A1: 2001 + A2: 2008
EN 62841-1: 2015 + AC: 2015
EN 62841-2-11: 2016 + A1: 2020
EN ISO 11680-1:2011
EN IEC 63000: 2018
The signatories act on behalf of and with the authority of
the company management.
Documentation supervisor:
English 15