Cleaning And Maintenance - Royal Catering RCGK-W200 Bedienungsanleitung

Initiate service programming
mode – ATTENTION! IT IS
RECOMMENDED NOT TO
INITIATE THE SERVICE MODE –
all the factory parameters were
set in this mode and changes
may result in incorrect device
operation.
Return to ambient temperature
display.
SYMBOL MODE
ON Compressor is active
Flashing Prevention of short operation
periods activated
ON Active defrosting
Flashing Active dripping
ON Fan ON
Flashing Delayed ventilator activation
after defrosting
ON Unit of temperature
Flashing Programming mode
ON Unit of temperature
Flashing Programming mode
DISPLAYING SETTINGS
1. Briefly press the SET button and the current setting
will be displayed.
2. To return to the standard screen briefly press SET or
wait for approximately 5 seconds.
CHANGING SETTINGS
1. Press and hold down the SET button for
approximately 3 seconds
2. The current setting will be displayed and °C or °F
diode will flash.
3. Change the setting using
4. To accept changes press the SET button.
LOCKING BUTTONS
Press and hold down the
least 3 seconds. „OF" will be displayed – the buttons are
now locked.
UNLOCKING BUTTONS
Press and hold down the
least 3 seconds. „on" will be displayed – the buttons are
now active.
TRANSPORTATION AND STORAGE
During transport, the machine should be protected from
shaking, falling and turning upside down. Store it in
a properly ventilated place with dry air and without any
corrosive gas.
Rev. 11.01.2018
DESCRIPTION
or .
and buttons for at
and buttons for at

CLEANING AND MAINTENANCE

It is recommended to wash the appliance regularly. Before
start of cleaning of the appliance or before performance
of any repair or maintenance work, it is necessary to
disconnect the appliance from the power supply and
wait until it has cooled down. Do not use for washing any
caustic cleaners, such as cleaning powders, agents with
alcohol content, thinners, diluents, etc., and do not allow
water to enter the appliance interior. Never immerse the
appliance, cord or plug in water or any other liquid. It is
forbidden to clean the device with a water jet. The interior
of the device should be cleaned with a disinfectant suitable
for the food industry. To clean, use a damp, soft cloth and
then dry thoroughly. Dry the surface with a soft, dry cloth.
The following actions should be taken if the machine is not
used for a long period of time: Disconnect the appliance
completely from the power supply and remove all food
products from it. Then wash the entire appliance with
a damp, soft cloth and mild cleaning agent, rinse with clean
water and dry thoroughly, for some time leave the door
open, so that the appliance will be completely dry. From
time to time, check that the cable is not damaged. Do not
use the appliance if the cable is damaged. A damaged cable
must be replaced by a service or a qualified electrician. In
the event of damage or malfunction, please contact your
dealer or our service. Maintenance and repair work must
be done only by qualified personnel using original spare
parts and accessories. Attempts to make repairs on your
own can lead to a direct threat to life or health, and will
void the warranty!
CHECK REGULARLY THE DEVICE
Check regularly that the device doesn ́t present any
damage. If there is any damage, please stop using the
device. Please contact your customer service to solve the
problem.
What to do in case of a problem?
Please contact your customer service and prepare following
information:
• Invoice number and serial number (the latter is to be
found on the technical plate on the device).
• If relevant, a picture of the damaged, broken or
defective part.
• It will be easier for your customer service clerk to
determine the source of the problem if you give
a detailed and precise description of the matter.
The more detailed your information, the better the
customer service will be able to answer your problem
rapidly and efficiently!
CAUTION: Never open the device without the authorization
of your customer service. This can lead to a loss of warranty!
TROUBLESHOOTING
Problem Probable cause
The The unit is not
appliance switched on
is not
working
Plug and lead are
damaged
Fuse in the plug has
blown
Action
Check the unit
is plugged in
correctly and
switched on
Call your agent
or qualified tech-
nician
Replace the fuse
11