Care And Maintenance - Lavorwash WTP Bedienungsanleitung

12
they understand the hazards involved. Cleaning
and user maintenance shall not be made by
children unless they are older than 8 and super-
vised. Children shall not play with the appliance.
•The equipment should be correctly assembled
before use.
• Ensure that power sockets used are correct
for the machine.
• Never grasp the power cord with wet han-
ds.
•Check that voltage indicated on the rating
plate is the same as the supply voltage.
•These machines are not suitable for vacuu-
ming health endangering dusts or inflamma-
ble/explosive substances (like ash and soot).
•
Never leave the equipment unattended
whilst in use.
• Never carry out any maintenance on the
machine without first disconnecting from the
mains supply or when it is left unattended or
reachable by children or disables..
• The power cord should not be used to pull or
lift the machine.
• The machine should never be immersed and
never use water jet against the appliance to cle-
an it.
• When using the machine in wet rooms
(e.g. in the bathroom) only connect it to so-
ckets which are connected in series with a
ground fault circuit interrupter. In case of
doubt, consult an electrician.
• Periodically examine the power cord and
machine for damage. If any damage is found,
do not use the appliance but contact your
service centre for repair.
If the supply cord is damaged, it must
•
be replaced by the manufacturer, its service
centres or similarly qualified people in order
to avoid a hazard.
• If an extension cord is used, the plug and so-
cket must be of watertight construction.
• Before vacuuming liquids, check the float
functions correctly. When vacuuming liquids,
and when the tank is full, a float closes the suc-
tion opening, and the vacuum operation is inter-
rupted. Then switch off the machine, disconnect
the plug and empty the tank. Regularly clean the
water level limiting device (float) and examine it
for signs of damages.
•If the machine overturns, it would be recom-
mended to stand it up before switching off.
• If foam or liquid escape from the appliance,
switch off immediately..
• The equipment should not be used to va-
cuum water from containers lavatories, tubs,
etc.
• Aggressive solvents or detergents should
not be used.
•Service and repairs must be carried out by quali-
fied personnel only. Only use manufacturer ori-
ginal spare parts for service repair.
•The manufacturer cannot be held responsible
for any damage/injury caused to persons, ani-
mals or property caused by misuse of the ap-
pliance,
USE
• Be sure that switch is in off position (0) OFF and
connect the machine to a suitable socket.
• The machine must be always kept on horizontal
bases, in a safe and stable way.
• Insert the suitable filters for the proper use. See
fig. (H)(L)(M)(N)(P).
•Never use the appliance without filters .
• Use the most suitable accessories for the reque-
sted usage (E)(F).
• Put switch on (|) ON position in order to start the
machine.
• When job is over, switch off (0) OFF and keep
away the plug from the socket.
• If the appliance is used with especially fine dust
(size below 0.3 µm) the filter supplied will requi-
re cleaning more frequently. For especially de-
manding applications, the use of specific filters
supplied as an optional (Hepa) may be necessa-
ry.
Outlet Models
see fig. (G)
To activate the socket-electric tool function, put
switch (4) on (|)ON and switch (5) on (0) OFF.
When a tool is connected the vacuum will
automatically start as the tool is started. The
suction hose will suck directly dust and wood
shavings.
• Even when switches (4) and (5) are (|) ON , the
electric tool socket is live. Not suitable for any
hot items.

CARE AND MAINTENANCE

see fig. (R)
The unit is maintenance-free.
• The machine shall be disconnected from its
power source, by removing the plug from the
socket-outlet, during cleaning or maintenance
• Clean the exterior part of the machine with a
dry cloth.
• Move the appliance only by catching the