Milwaukee Heavy Duty BTT Originalbetriebsanleitung Seite 2

TECHNICAL DATA
Voltage
Weight with battery
Battery life
Recommended Ambient Operating Temperature -20°C to 60 °C
Signal Range
Impact resistance level
Protection Class
Frequency band(s) of Bluetooth 2402-2480 MHz
Maximum radio-frequency power transmitted in the frequency band(s)
WARNING
Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may result in electric
shock, fi re and/or serious injury.
Save all warnings and instructions for future reference.
SAFETY INSTRUCTIONS BATTERY
Battery acid may leak from damaged batteries under extreme load or
extreme temperatures. In case of contact with battery acid wash it off
immediately with soap and water. In case of eye contact rinse
thoroughly for at least 10 minutes and immediately seek medical
attention.
This appliance is not intended for use by persons (including children)
with limited physical, sensory or mental capabilities or insuffi cient
experience and/or knowledge unless they are supervised by a person
who is responsible for their safety or have been instructed by them in
the safe use of the tool.
2
Children should be supervised in order to ensure that they do not play
with the tool.
3,0 V
WARNING This device contains a lithium button/coin cell
17 g
battery. A new or used battery can cause severe internal burns
3 years
and lead to death in as little as 2 hours if swal lowed or enters
the body. Always secure the battery cover. If it does not close securely,
≥ 30 m
stop using the device, remove the batteries, and keep it away from
IK06
children. If you think batteries may have been swallowed or entered the
IP68 body, seek immediate medical attention.
Warning! To reduce the risk of fi re, personal injury, and product
1.8 dBm damage due to a short circuit, never immerse your tool, battery pack or
charger in fl uid or al-low a fl uid to fl ow inside them. Corrosive or
conductive fl uids, such as seawater, certain industrial chemicals, and
bleach or bleach containing products, etc., Can cause a short circuit.
SPECIFIED CONDITIONS OF USE
The Tracker is designed to track tools and equipment using the
ONE-KEY™ App.
Do not use this product in any other way as stated for normal use.
EC-DECLARATION OF CONFORMITY
Hereby, Techtronic Industries GmbH declares that the radio equipment
type BTT is in compliance with Directive 2014/53/EU. The full text of
the EU declaration of conformity is available at the following internet
address: http://services.milwaukeetool.eu.
ENGLISH
GB-DECLARATION OF CONFORMITY
Hereby, Techtronic Industries GmbH declares that the radio equipment
type BTT is in compliance with Directive S.I. 2017/1206 (as amended).
The full text of the GB declaration of conformity is available at the
following internet address: http://services.milwaukeetool.eu.
ONE-KEY™ APP / ACCOUNT SET UP
1. To download the ONE-KEY™ app, visit the App Store or Google
Play from your smart device.
2. Create a User Name and Password and log in to a ONE-KEY™
account.
3. Bluetooth and Location Services must be enabled on your mobile
device.
4. Location Services must be enabled in the Settings section of the
App.
ACTIVATING THE TRACKER
1. To begin, scan the QR code on top of the Tracker with the camera
app on an iOS or Android device. When successful, the device will
provide guidance for installing the One-Key app.
2. Scanning the QR Code after the app is installed will launch the
One-Key app and provide guidance through the activation process.
3. Upon activation an audible tone will be heard, indicating the Tracker
is ready to use.
INSTALLING THE TRACKER
The tracker is designed to track tools and equipment using the
ONE-KEY™ App. It will not prevent theft from happening. The tracker
can be attached in a variety of orientations.
Consider attaching the tracker to prevent tampering.
The tracker can be attached using the following options
• • #8 Pan Head Self Tapping Screw
• • Glue or Epoxy
• • 4mm Diameter Rivet
• • Cable or zip tie
• • Key ring
WARNING! Do not secure in such a way as to impede the safe use of
the product. Do not attach on or near the following:
• vents
• moving parts
• safety notifi cation
• guards
• hand holds
• switches or controls
• areas exposed to sparks or heat
Before using screws or rivets, ensure the space behind the placement
is clear.
MAINTENANCE
Clean with a damp, soft cloth.
Never use aggressive cleaning agents or solvents.
ENGLISH 3