Coleman Airbed Wrap 'N' Roll Bedienungsanleitung Seite 4

GB Instruction leaflet with Wrap'N'Roll
IMPORTANT INFORMATION
• CAREFULLY READ THE INSTRUCTION MANUAL BEFORE
USE.
• DISCARD RED TUBE LOCATED ON THE EXTERNAL
STOPPER OF THE INFLATION VALVE. IT IS THERE FOR
SHIPPING PURPOSES
CHILDREN.
• DO NOT LET INFLATABLE PRODUCTS COME IN CONTACT
WITH SHARP, POINTED OBJECTS THAT MAY PUNCTURE
THE PLASTIC MATERIAL.
• FILL WITH COLD AIR ONLY. NEVER USE A HAIR DRYER
TO INFLATE, THIS COULD CAUSE MELTING.
• DO NOT OVER INFLATE. BURSTING ITEMS CAN CAUSE
SERIOUS INJURY. INFLATE THE AIRBED UNTIL MOST OF
THE WRINKLES IN THE MATERIAL ARE GONE AND THE
BED FEELS FIRM TO THE TOUCH.
Caution: air temperature and weather do affect the air pressure in
inflatable products. In cold weather your airbed will lose some pressure
due to the fact that the air will contract.
If this occurs, you may want to add a little air to improve your airbed's
performance. However, in hot weather, the air will expand.
You must let some air out to prevent the airbed from failing due to
overpressure. You should avoid exposing your airbed to extreme
temperature (hot or cold).
. WARNINGS
1
• DO NOT USE THIS AIRBED AS A RAFT OR A BOAT.
• DO NOT INFLATE WITH AN AIR COMPRESSOR.
• KEEP AWAY FROM FIRE.
2. INFLATION INSTRUCTIONS
2.1 To inflate using Coleman
• Open the valve (A).
• Pull the external stopper to extend the valve out (B).
• Attach adapter nozzle of the pump to the airbed valve by
twisting it gently. Turn on the pump to inflate (C).
• When fully inflated, seal valve by pushing in with pump nozzle.
• Gently twist adapter sleeve to right, backing the pump out of
valve while maintaining the seal (D).
• Close the external stopper.
• Valve should appear depressed into itself (E).
2.2 To inflate using foot pump* or other inflation device
Important: the nozzle must fit snugly into extended valve for
good inflation results.
• To begin inflation, open external stopper and pull to extend out
(B).
• Insert nozzle of inflation device into the extended valve and
turn on or begin pumping (D).
• To close valve: push in with inflation device until stopper has
been depressed, sealing internal stopper. Remove device and
close external stopper. Valve should appear depressed into
itself (E).
* Note: pump is sold separately.
3. DEFLATION INSTRUCTIONS
®
3.1 Using Campingaz / Coleman
• Remove adapter nozzle from inflation end and attach to
opposite deflation side of the pump.
• Repeat same steps as inflation. This will draw the air out very
quickly.
3.2 Without use of pump* (B)
• To deflate, open external stopper and pull to extend out
allowing air to escape.
• When fully deflated, close stopper.
4. TAKING CARE OF YOUR AIRBED
• Make sure product is completely dry and clean before deflating
and storing.
• Clean product with mild soap and water only. Do not use any
strong detergents.
ONLY. KEEP AWAY FROM
®
pump*
®
pump* (F)
TM
TM
5. WRAP 'N' ROLL STORAGE SYSTEM
Storage Steps
• Deflate Airbed. (Step 1) (Leaving the Double Lock
while rolling will help remove any remaining air for more compact
storage.)
• Fold bed as shown. (Step 2)
• Roll up the Airbed toward the storage flap. (Step 3)
• Wrap storage flap around rolled bed and tie ends to secure.
(Step 4)
De fla tion
V a lve
St e p 2
Fold be d
TM
Valve open
St e p 1
De fla te be d
Double Loc k
T M
V a lve
St e p 3
Roll be d
St e p 4
Se c ure be d
4