Kress KUC61 Bedienungsanleitung Seite 8

cause inferior quality SDS bits to break and jam in
the chuck，We therefore recommend that only high
quality SDS bits be used with this tool.
2. AUXILIARY HANDLE (SEE FIG. B)
Slide the handle onto the hammer and rotate to the
desired working position. To clamp the auxiliary handle
rotates the handle clockwise. To loosen the auxiliary
handle, rotate the handle counter-clockwise.
WARNING: Always use the auxiliary
handle.
3. ADJUSTABLE DEPTH GAUGE (SEE FIG. B)
Loosen the depth gauge by rotating the handle
counter-clockwise. Slide the depth gauge until the
distance between the depth gauge end and the drill
bit end is equal to the depth of hole/screw you wish
to make. Then clamp the depth gauge by rotating the
handle clockwise.
4. ON/OFF SWITCH (SEE FIG. C)
Depress the On/Off switch (5) to start and release it to
stop your tool.
— ON/OFF SWITCH WITH VARIABLE SPEED
CONTROL
Depress the On/Off switch to start and release it to
stop your tool. This tool has a variable speed switch
(5) that delivers higher speeds with increased trigger
pressure or delivers lower speeds with reduced trigger
pressure - speed is controlled by varying the pressure
8
applied to the switch.
EN
5. SWITCH LOCK (SEE FIG. C)
The switch trigger can be locked in the OFF position.
This helps to reduce the possibility of accidental
starting when not in use. To lock the switch trigger,
place the direction of rotation control in the center
position.
6. FORWARD AND REVERSE ROTATION
CONTROL (SEE FIG. C)
Forward rotation: Push the forward and reverse
rotation control to the left "
Reverse rotation: Push the forward and reverse
rotation control to the right "
drill bits.
WARNING: Never change the direction of
rotation while the tool is rotating, wait
until it has stopped.
7. AUXILIARY FUNCTION ON TILE
1) Press ON/OFF switch to see the light is on or off.
Light on indicates the auxiliary function is on, and light
off indicate the auxiliary function is turn off.
2) When operating on the tile, press the auxiliary
function button on tile (10) first, the green light on
means that auxiliary function is on, then half-press
switch, begin pulse auxiliary operation. Until the glaze
of tile is broken, press the ON/OFF switch to the
bottom and begin the drilling .
3) When operating on things rather than tile, keep the
auxiliary function button closed, to insure the high
efficiency when drilling.
", for drilling
", for removing the
Note:
a) Auxiliary function on tile avoids the unexpected
split of tile. This auxiliary function takes the place of
previous pre-drilling by glass drill on tile.
b) The auxiliary function on tile is only suitable to
be used under the hammer drilling position. When
operating under drilling/chiseling/ Adjust the chuck
angle mode, make sure to turn the auxiliary function off .
8. FUNCTION MODE SELECTION (SEE FIG. D)
The operation of the gearbox for each application
is set with the function selector dial (4). To change
between functions, depress the unlocking button (a)
and rotate the selector to the desired operating mode.
Mode for simultaneous drilling
and impacting of concrete,
Masonry
Mode for or drilling into steel,
wood and plastics
Mode for or chiseling
Mode for adjust the chuck angle
of chiseling
NOTE: Select this function mode
first, adjust the chuck angle to
desired direction. Then select the
function mode to "
the chiseling work.
WARNING: The operating mode selector
switch may be actuated only at a
standstill.
9. OVERLOAD PROTECTION
When overloaded, the motor comes to a stop. Relieve
the load on the machine immediately and allow
cooling for approx. 30 seconds at the highest no-load
speed.
10. TEMPERATURE DEPENDENT OVERLOAD
PROTECTION
When using as intended for, the power tool cannot be
subject to overload. When the load is too high or the
allowable battery temperature of 75 °C is exceeded,
the electronic control switches off the power tool until
the temperature is in the optimum temperature range
again.
11. PROTECTION AGAINST DEEP DISCHARGING
The Li-ion battery is protected against deep
discharging by the "Discharging Protection System".
When the battery is empty, the machine is switched off
" , operate