Felisatti S254/1800 Bedienungsanleitung Seite 9

activated lock lever is located on top of the switch handle.
To turn the machine on, press the ON/OFF switch 4
and keep it pressed down.
When the ON/OFF switch is released, the machine
stops.
WARNING! Make the switch child-proof. Insert a
padlock through the hole in the trigger switch and lock it.
This will prevent children and other unauthorized users
from engaging the trigger switch ON.
Before leaving the saw
Never leave tool running unattended. Turn power
OFF. Wait for all moving parts to stop and unplug unit from
power source.
Make workshop child- proof. Lock the shop.
Disconnect master switches. Store tool away from children
and other unqualified users.
WARNING! To avoid injury from materials being
thrown, always unplug the saw to avoid accidental starting
, and remove small pieces of material from the table cavity.
WARNING! For your convenience, your saw has a
blade brake. The brake is not a safety device. Never rely on
it to replace the proper use of the guard on your saw. If the
blade does not stop within approximately 6 seconds, wait
for the blade to stop, unplug the saw and contact Service
Center.
The laser guide
To turn laser on, turn switch 48 to «I» position.
1
2 To turn laser off, turn switch 48 to «O» position.
Note.
● All the adjustments for the operation of the laser guide
have been completed at the factory.
● Laser beam is calibrated and set up to project to the
left of the blade.
● If you have any problem or question on the laser
guide, please call the Service Center.
WARNING! Laser is radiated when laser guide
is turned on. Avoid direct eye contact. Always un-plug
the miter saw from power source before making any
adjustments.
WARNING! Do not attempt to repair or disassemble
the laser. If unqualified persons attempt to repair this laser
product, serious injury may result. Any repair required on
this laser product should be performed by a Sears or other
qualified service center.
Starting a cut:
- Place hands away from the path of the blade - out of
the «no-hands zone».
- Hold workpiece firmly against the fence to prevent
movement toward the blade.
- With the power switch OFF, bring the saw blade down
to the workpiece to see the cutting path of the blade.
- Press in lock-off switch in trigger switch handle.
- Squeeze trigger switch to start saw.
- Lower blade into workpiece with a firm downward
motion.
Finishing a cut:
- Hold the cutting arm in the down position.
- Release trigger switch and wait for all moving parts to
stop before moving your hands and raising the cutting arm.
- If the blade doesn't stop within 6 seconds, unplug the
saw and follow the instructions in TROUBLESHOOTING
GUIDE section.
Before freeing jammed material:
- Release trigger switch.
- Wait for all moving parts to stop.
- Unplug the miter saw.
BASIC SAW OPERATIONS
Miter cut
1 Choose the left or right sliding fence unit to perform
the miter cutting.
2 If the left sliding fence unit 9 is chosen, unlock the left
sliding fence unit by unlocking the positive stop lock lever
41 behind the left sliding fence unit and lifting up the lock
lever 16 pivotally connected in the base.
3 Slide the left sliding fence unit to the desired angle
from 0° to 45° forward.
If the desired angle is one of the positive stops 40,
4
tighten the positive stop lock lever, and then flip the lock
lever down to lock the sliding fence unit. Positive stops for
miter cutting are provided at 0°, 22.5° and 45°.
5 If the desired angle is not one of positive stops, simply
lock the sliding fence unit by flipping the lock lever 16 down.
6 For avoiding the interference caused by the right
sliding fence unit during cutting operation, lock the right
sliding fence at the angle 45° forward.
7 Unlock the right sliding fence plate by loosening the
knob, and slide the right sliding fence plate rightward to the
distal end, and tighten the knob.
8 Place the workpiece against the left sliding fence unit
and secure the workpice by the vise to perform the miter
cutting.
9 If the right sliding fence unit is chosen, inversely adjust
the two sliding fence units according to the procedure
foregoing 2-8.
Important:
● Secure the fence unit before performing the cutting.
● Always position the rest sliding fence unit at the angle
45° forward when one of the sliding fence units is used in
cutting.
Bevel cut
1 When a bevel cut is required, loosen the bevel lock
handle for angle adjusting.
2 Tilt the cutting head to the desired angle as shown on
the bevel scale. The blade can be positioned at any angle,
from a 90° straight cut (0° on the scale) to a 45° left bevel.
3 Unlock the left sliding fence plate by loosening the
knob, and slide the plate leftward for avoiding interference,
and tighten the knob.
4 Tighten the bevel lock handle to lock the cutting head
in position.
5 Positive stops are provided at 0° and 45°.
Important: Secure the sliding fence unit before
performing the cutting.
Compound cut
A compound cut is the combination of a miter and a
bevel cut simultaneously.
1 Unlock the left sliding fence unit by unlocking the
positive stop lock lever behind the left sliding fence unit
and lifting up the lock lever pivotally connected in the base.
2 Slide the left sliding fence unit to the desired angle
from 0°~ 45° forward.
3 If the desired angle is one of the positive stops,
tighten the positive stop lock lever, and then flip the lock
lever down to lock the sliding fence unit. Positive stops for
compound cutting are provided at 0°, 22.5° and 45°.
4 If the desired angle is not one of positive stops, simply
lock the sliding fence unit by flipping the lock lever down.
5 Unlock the left sliding fence plate by loosening the
knob, and slide the left sliding fence plate leftward for
avoiding interference, and tighten the knob.
6 Lock the right sliding fence at the angle 45° forward,
9