Herunterladen Inhalt Inhalt Diese Seite drucken

Felisatti S254/1800 Bedienungsanleitung Seite 11

Gehrungssäge
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 38
motor damage and the tools should be changed when any
abrasion is noted. Daily: Clean the tool holder.
-
Inspect the mounting screws: Regularly inspect all
the mounting screws and ensure they are firmly tightened.
Should any screw be loose, tighten it immediately. Failure
to do so could put you at serious risk.
-
Motor maintenance: Take the utmost care to ensure
that the motor winding is not damaged and does not
become damp with oil or water.
-
Brush replacement: Check the motor brushes after the
first 50 hours of use for a new machine or after a new set of
brushes have been installed. After the first check, examine
them every 10 hours of use. When the carbon is worn to
6 mm in length or if the spring or shunt wire is burned or
damaged, replace both brushes. Have them replaced by an
Official Service Centre.
-
Clean the machine thoroughly after each use with a
blast of dry air.
-
The vents of the machine should be kept clear at all
times.
-
Check that the mains lead is in good condition. If it is
not, take it to an Official Service Centre to have it replaced.
Trouble shooting guide
Brake does
1. Motor brake
not stop
overheated from use of
blade within
defective or wrong size
6 seconds.
blade or rapid ON/OFF
cycling.
2. Arbor bolt loose.
3. Brushes cracked,
damaged, etc.
4. Other.
Motor does
1. Brush worn.
not start
2. Fuse blown or circuit
breaker tripped on home
panel.
3. There is no power at
the outlet.
Brush spark
1. Brush worn.
when switch
2. Other.
released.
Blade hits
Misalignment.
table.
Angle of cut
1. Miter table unlocked.
not accurate.
2. Sawdust under table.
Can not
adjust miter.
Cutting arm
Loose pivot points.
wobbles.
Cutting arm
1. Pivot spring not
will not fully
replaced properly after
raise, or
service.
blade guard
2. Sawdust build-up.
won't fully
close.
1.Use a recommended
blade. Let cool down.
See REMOVING OR
INSTALLING THE BLADE
section.
2. Retighten. See
REMOVING OR
INSTALLING THE BLADE
section.
3-4. Contact Service Center
to change brushes.
1-2. Contact Service Center
to change brushes.
3. Verify there is electrical
power at the outlet.
1-2. Contact Service Center
to change brushes.
See ADJUSTMENT-
CUTTING ARM TRAVEL
section.
1. See OPERATION - Miter
Angle Adjustment section.
2. Vacuum or blow
out dust. WEAR EYE
PROTECTION.
Contact Service Center.
1. Clean and lubricate
moving parts.
2. Contact Service Center.
Blade binds,
1. Improper operation.
jams, burns
2. Dull or warped blade.
wood.
3. Improper blade size.
4. Wood is moving
during cut.
Saw vibrates
1. Saw blade not round/
or shakes.
damaged / loose.
2. Arbor bolt loose.
Repair
Use only FELISATTI accessories and spares. The
parts the changing of which is not covered in this instruction
manual, should be replaced in a FELISATTI Official Service
Centre (See Warranty/Official Service Centre address
leaflet).
WARRANTY
See general warranty conditions printed on the
attached sheet.
DISPOSAL
WARNING! Do not dispose of electric tools in the
household waste!
In accordance with European Directive 2002/96/EC
relating to old electrical and electronic appliances and
its translation into national law, used electric tools must
be collected separately and recycled in an ecologically
desirable way.
1. See BASIC SAW
OPERATION section.
2. Replace or sharpen
blade.
3. Replace with 255 mm
diameter blade.
4. Use clamp device to
secure workpiece to fence
unit and table.
1. Replace blade.
2. Tighten arbor bolt.
11

Werbung

Inhaltsverzeichnis
loading

Inhaltsverzeichnis