Declaration Of Conformity - Felisatti S254/1800 Bedienungsanleitung

workpiece is clear of any adjusting tools, wood chips, etc.
Small pieces of wood or other objects that come in contact
with the rotating saw blade can strike the operator with high
speed.
Keep the floor free of wood chips and material
remainders. You could slip or trip.
Always firmly clamp the piece to be worked. Do not
saw workpieces that are too small to clamp. Otherwise,
the clearance of your hand to the rotating saw blade is too
small.
Use the machine only for cutting the materials listed
under Intended Use. Otherwise, the machine can be
subject to overload.
If the saw blade should become jammed, switch
the machine off and hold the workpiece until the saw
blade comes to a complete stop. To prevent kickback,
the workpiece may not be moved until after the machine
has come to a complete stop. Correct the cause for the
jamming of the saw blade before restarting the machine.
Do not use dull, cracked, bent or damaged saw blades.
Unsharpened or improperly set saw blades produce narrow
kerf causing excessive friction, blade binding and kickback.
Always use saw blades with correct size and shape
of arbor holes. Saw blades that do not match the mounting
hardware of the saw will run eccentrically, causing loss of
control.
Do not use high speed steel (HSS) saw blades. Such
saw blades can easily break.
Do not touch the saw blade after working before it has
cooled. The saw blade becomes very hot while working.
Check the cable regularly and have a damaged cable
repaired only through an authorised customer service agent
for FELISATTI. Replace damaged extension cables. This
will ensure that the safety of the power tool is maintained.
Store the machine in a safe manner when not being
used. The storage location must be dry and lockable. This
prevents the machine from storage damage, and from
being operated by untrained persons.
Do not direct the laser beam at persons or animals
and do not stare into the laser beam yourself, not even from
a distance. This can lead to persons being blinded.
Do not replace the installed laser with another laser
type. A laser that does not fit to this power tool could pose
dangers for other persons.
Secure the workpiece. A workpiece clamped with
clamping devices or in a vice is held more secure than by
hand.
Never leave the machine before it has come to a
complete stop. Cutting tools that are still running can cause
injuries.
Never use the machine with a damaged cable. Do not
touch the damaged cable and pull the mains plug when the
cable is damaged while working. Damaged cables increase
the risk of an electric shock.
Other safety information
Be sure the power supply is same as the voltage given
on the rating plate. The tool is fitted with a two-core cable
and plug.
Remove the power plug from socket before carrying
out any adjustment or servicing.
Residual risks
Even when the power tool is used as prescribed
it is not possible to eliminate all residual risk
factors. The following hazards may arise in connection with
the power tool's construction and design:
- Damage to lungs if an effective dust mask is not worn.
- Damage to hearing if effective hearing protection is
not worn.
- Damages to health resulting from vibration emission if
the power tool is being used over longer period of time or
not adequately managed and properly maintained.
WARNING! This
electromagnetic field during operation. This field may under
some circumstances interfere with active or passive medical
implants. To reduce the risk of serious or fatal injury, we
recommend persons with medical implants to consult their
physician and the medical implant manufacturer before
operating this machine.

DECLARATION OF CONFORMITY

12
Business name of the manufacturer:
INTERSKOL POWER TOOLS S.L.
Full address of the manufacturer
Ctra. de St. Joan de les Abadesses, s/n
17500 RIPOLL (Girona) SPAIN
Name and address of the person
(established in the Community) compiled
the technical file:
Jordi Carbonell, Santiago López
Ctra. de St. Joan de les Abadesses, s/n
17500 RIPOLL (Girona) SPAIN
Product name: Miter saw
Commercial name: Miter saw
Models: S254/1800
Type: Electric power tools
Serial Number: see label of the tool
We hereby declare, under our sole
responsibility,
brand products described in this manual
S254/1800 comply with the following
standars or standard documents:
Machinery Directive 2006/42/EC; the
Low Voltage Directive 2006/95/EC; the
EMC Directive 2004/108/EC and conform
to EN ISO 12100:2010; EN61029-
1:2009+A11:2010; EN61029-2-9:2009.
Jordi Carbonell
We reserve the right to make technical changes 12/2012
power tool produces
that the FELISATTI
Santiago López
an
5