Filter; Breathing Hose; Breath Connection/Headpiece - e-breathe e-Flow Gebrauchsanweisung

2.2 Filter

The choice of filter depends, among other things, on the type of contamination and the concentration. The blower
can be used either with only two particle filters, two gas filters or with two combination filters (combination of particle
and gas filter). (See separate instructions for use of the filters).
The following filters are available for the e-breathe e-Flow with PAD-Box
Filter
e-breathe ecoPAD P3 R / PSL
e-breathe ecoPAD GF A2
e-breathe ecoPAD GF A2B2
e-breathe ecoPAD GF A2B2E1K1
The following filters are available for the e-breathe e-Flow with filter box
Filter
e-breathe Particle Filter P3 R / PSL
e-breathe Combination Filter A2-P3
e-breathe Combination Filter A2B2-P3
e-breathe Combination Filter A2B2E1K1-P3
Particle Filter
Type / Color main application area
Class Code
P3 white P = For use against solid and liquid toxic, radioactive and harmful particles as well as microorga-
nisms such as bacteria and viruses.
R R (reusable) = The particle filter is intended for multiple use and can be used throughout several
working shifts.
SL SL (Solid Liquid) = The particle filter is designed for use against solid and liquid aerosols.
Gas Filter A, B, E, K, HG
Type Color main application area
Code
A
brown Protects against organic gases and vapours.
e.g. solvent with a boiling point above +65 °C
B grey Protects against inorganic gases and vapours.
e.g. chlorine, hydrogen sulphide and hydrocyanic acid
(not against CO)
E
yellow Protects against acid gases and vapours.
e.g. sulphur dioxide and hydrogen fluoride
K green Protects against ammonia and certain amines.
e.g. ethylenediamine
HG red Protects against mercury vapour.
Warning! Maximum application time 50 hours.
36
e-breathe e-Flow
can be combined with:
Gas filter Adapter and ecoPAD GF A2, A2B2, ABEK
Filter Cover and ecoPAD P3 R / PSL
Filter Cover and ecoPAD P3 R / PSL
Filter Cover and ecoPAD P3 R / PSL
can be combined with:
Gas Filter Adapter and ecoPAD GF A2, A2B2, ABEK
ecoPAD P3 R / PSL and ecoPAD GF A2, A2B2, ABEK
ecoPAD P3 R / PSL and ecoPAD GF A2, A2B2, ABEK
ecoPAD P3 R / PSL and ecoPAD GF A2, A2B2, ABEK
Class Permitted maximum
gas concentration
1 0,05 Vol-%
2 0,1 Vol-%
3 0,5 Vol-%
1 0,05 Vol-%
2 0,1 Vol-%
3 0,5 Vol-%
1 0,05 Vol-%
2 0,1 Vol-%
3 0,5 Vol-%
1 0,05 Vol-%
2 0,1 Vol-%
3 0,5 Vol-%
1 Observe
2 manufacturer's ins-
3 tructions for use
info@e-breathe.de • www.e-breathe.de
Rev. 0.7 Important!
• Always use two filters.
• The particle, gas or combination filters used must be of the same type.
• Both particle, gas or combination filters must be replaced at the same time in case of a filter replacement.
Prefilter
The pre-filter protects the main filter from premature clogging and handling damage. The prefilter must be inserted
into the prefilter holder. Important! The prefilter can only be used as a prefilter. It can never be used as a replacement
for a particle filter.

2.3 Breathing Hose

The breathing hose is not included in the scope of delivery of the blower or the respective head piece. The breathing
hoses are available separately.
The breathing air hose has a round thread connection for the side that is attached to the blower.
The following connections are available for the other connection side, which is attached to the breath connection:
• e-breathe Click plug-in connection g for overpressure hoods and blower protection suits
• e-breathe Vario & MM plug-in connection g for blower-assisted face shield Multimask and Multimask Pro
• DIN-round thread connection g for full face masks and half masks
2.4 Breath Connections/Headpiece
The choice of the head piece depends on the working conditions, the work tasks and the required protection factor.
See page 57 for available and approved headtops.
The devices are divided into equipment classes according to their respiratory protection performance. The following Table
1 applies:
Device Class VdgW (GW1)
Helmets / Hoods / Suit with blower and particle filters
TH2P 20
TH3P 100
Half masks / full masks with blower and particle filters
TM2P 100
TM3P 500
Helmets / hoods / suit with blower and gas filters (*2)
TH2 Gas filter class 1,2,3 20
TH3 Gas filter class 1,2,3 100
Half masks / full masks with blower and gas filters (*2)
TM2 Gas filter class 1,2,3 100
TM3 Gas filter class 1,2,3 500
The specifications also apply analogously to combination filters.
• VdgW: multiple of the limit value, DGUV regulation 112-190 Use of respiratory protection devices
• GW1 are e.g. the limit values in the air at the workplace listed in TRGS 900 - MAK and TRK values (MAK = maximum workplace concentration; TRK = technical
standard concentration).
• (* 2) Unless the maximum permissible concentrations for gas filters in blower filter units of 0.05 vol-% in gas filter class 1, 0.1 vol-% in gas filter class 2 and 0.5 vol-%
in gas filter class 3, based on the gas absorption capacity, are already exceeded.
• Leakage: Permissible maximum percentage for the total inward leakage
e-breathe e-Flow
Leakage* Remarks / Restrictions
2% -
0,2% -
0,5% -
0,05% -
2% -
0,2% -
0,5% -
0,05% -
info@e-breathe.de • www.e-breathe.de
Rev. 0.7
37