Inhaltsverzeichnis
Werbung
CONNECTION
Warning! Danger of death through electric shock!
- must be installed by professional electrician
- disconnect power source
- cover or shied any adjacent live components
- check power supply is disconnected
Turn the bottom-cover anti-clockwise and unload it.
The power wire goes across the hole in the middle of bottom-stand. Connect the power wire into connec-
tion-wire column according to the connection-wire diagram.
Fix the bottom-stand on the selected position with in ated screw.
The sensor should be aimed at the mouth of bottom-stand and turned clockwise.
After nishing installing, turn on the power and then test it.
TEST
Turn the TIME knob anti-clockwise on the minimum(10s).Turn the LUX knob clockwise on the maximum (sun).
Switch on the power; the sensor and its connected lamp will have no signal at the beginning. After Warm-up 30sec, the
sensor can start work .If the sensor receives the induction signal, the lamp will turn on. While there is no another induction
signal any more, the load should stop working within 10sec±3sec and the lamp would turn o .
Turn LUX knob anti-clockwise on the minimum (3). If the ambient light is more than 3LUX, the sensor would not work and
the lamp stop working too. If you cover the detection window with the opaque objects (towel etc), the sensor would work.
Under no induction signal condition, the sensor should stop working within 10sec±3sec.
NOTE: When testing in daylight, please turn LUX knob to
could not work! If the lamp is more than 60W, the distance between lamp and sensor should be 60cm at
least.
MOST COMMON PROBLEMS AND SOLVING WAYS
The load do not work:
1) Please check if the connection-wiring of power and load is correct.
2) Please check if the load is good.
3) Please check if the working light sets correspond to ambient light.
The sensitivity is poor:
1) Please check if there has any hindrance in front of the detection
window to a ect to receive the signal.
2) Please check if the ambient temperature is too high.
TECHNISCHE DATEN
Stromversorgung
Nennlast
Leistungsaufnahme
Standby-Leistung
Erfassungsreichweite
Umgebungslicht
FUNKTION
Kann Tag und Nacht erkennen: Der Verbraucher kann einstellen Arbeitszustand
in unterschiedlichen Umgebungslicht. Es kann in der Tag und Nacht arbeiten,
wenn er auf der "Sonne" Position (max) eingestellt. Es kann in der Umgebungs-
licht weniger als 3LUX arbeiten, wenn es auf der "3" Position (min) eingestellt.
Wie für die Justierungsmuster nden Sie in der Testmuster beziehen.
Verzögerungs- kontinuierlich zugegeben: wenn es innerhalb der ersten
Induktions empfängt die zweite Induktionssignale, wird es zu der Zeit von dem
Zeitpunkt erneut zu starten.
(SUN) position, otherwise the sensor lamp
230V~ 50Hz
1200W
300W
P
: <0.5W
on
P
: <0.5W
sb
Ø6m max (<24°C)
3 ÷ 2000lx (adjustable)
3) Please check if the induction signal source is in the detection elds
4) Please check if the installation height corresponds to the height
showed in the instruction.
5) Please check if the moving orientation is correct.
The sensor can not shut o the load automatically:
1) Please check if there is continual signal in the detection eld.
2) Please check if the time delay is the longest.
3) Please check if the power corresponds to the instruction.
DE
Erfassungsbereich
Zeitverzögerung
Arbeitsfeuchtigkeit
Arbeitsfeuchtigkeit
Einbauhöhe
Bewegungsgeschwindigkeit
Gute Emp ndlichkeit
360º
min: 10sec ± 3sec
max:7min±2min
-20~+40°C
<93%RH
max: 2.2m~4m
0.6~1.5m/s
Geringe Emp ndlichkeit
Werbung
Inhaltsverzeichnis
