Technical Data; Specified Conditions Of Use; Additional Battery Safety Warnings - AEG BUS18SBL Übersetzung Der Originalanleitung

TECHNICAL DATA

Type
Production code
Stroke rate under no-load
Length of stroke
Battery voltage
Weight without battery pack
Weight according to EPTA-Procedure 01/2014 (Li-ion 2.0 Ah ... 9.0 Ah)
Recommended ambient operating temperature
Recommended battery types
Recommended charger
Noise Information
Measured values determined according to EN 62841. Typically, the A-weighted noise
levels of the tool are:
Sound pressure level / Uncertainty
Sound power level / Uncertainty
Wear ear protection!
Vibration Information
Vibration total values (triaxial vector sum) determined according to EN 62841.
Vibration emission value / Uncertainty
Cutting board
Cutting wooden beam
WARNING!
The declared vibration total values and the declared noise emission values given in this instruction manual have been measured in
accordance with a standardised test and may be used to compare one tool with another. They may be used for a preliminary assessment of
exposure.
accessories, keeping the hands warm (in case of vibration), and organising work patterns.
WARNING! Read all safety warnings, instructions,
Failure to follow all instructions listed below may result in electric
for future reference.
RECIPROCATING SAW SAFETY WARNINGS
Cutting accessory contacting a "live" wire
may make exposed metal parts of the power tool "live" and could
give the operator an electric shock.
against your body leaves it unstable and may lead to loss of control.
ADDITIONAL SAFETY AND WORKING INSTRUCTIONS
Clamp the workpiece with a clamping device. Unclamped
immediately if it stalls. Do not turn on the product again while it is
still stalled, as doing so could trigger a sudden recoil with a high
reactive force. Determine why the product stalled and rectify this,
paying heed to the safety instructions.
The dust produced when using the product may be harmful to
health. Do not inhale the dust. Wear a suitable dust protection mask.
Remove the battery pack before starting any work on the product.
16
Holding the workpiece by hand or
ENGLISH
Cordless reciprocating saw
4757 92 01 XXXXXX MJJJJ
L =87.0 dB (A) / K
pA
L =98.0 dB (A) / K
WA
a
h,B
a
h ,WB

SPECIFIED CONDITIONS OF USE

The reciprocating saw is intended to cut wood, plastics, and metal.
The product can cut straight lines, curves, and internal cut-outs. The
Do not use the product for any other purpose.

ADDITIONAL BATTERY SAFETY WARNINGS

WARNING!
product damage due to a short circuit, never immerse your tool,
chemicals, and bleach or bleach containing products, etc., can
cause a short circuit.
Do not dispose of used battery packs in the household refuse or
protect our environment.
Use only AEG chargers for charging AEG battery packs. Do not use
battery packs from other systems.
Never break open battery packs and chargers, and store them only
in dry rooms. Keep battery packs and chargers dry at all times.
Battery packs that have not been used for some time should be
recharged before use.
Temperatures in excess of 50°C (122°F) reduce the performance of
the battery pack. Avoid extended exposure to heat or sunshine (risk
of overheating).
The contacts of chargers and battery packs must be kept clean.
For an optimum life-time, the battery packs have to be fully charged
after use.
BUS18SBL
0-3200 min
-1
22 mm
18 V
1.78 kg
2.20 ... 2.95 kg
-18...+50 ºC
L18...
AL18G, BL1...
=5 dB(A)
pA
=5 dB(A)
WA
=7.5 m/s / K=1.5 m/s
2 2
=8.0 m/s / K=1.5 m/s
2 2