Herunterladen Inhalt Inhalt Diese Seite drucken

Technical Data - AEG BUS18CBL Originalbetriebsanleitung

Vorschau ausblenden Andere Handbücher für BUS18CBL:
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 20

TECHNICAL DATA

Production code...............................................................................................................
Battery voltage.................................................................................................................
Stroke rate under no-load ................................................................................................
Lengths of stroke .............................................................................................................
Cutting depth max. in:
Soft wood .....................................................................................................................
Steel plate ....................................................................................................................
PVC Pipes / Sections ..................................................................................................
Weight (without Battery) ..................................................................................................
Weight according EPTA-Procedure 01/2014 (2,0 Ah - 9,0 Ah) ........................................
Recommended ambient operating temperature ..............................................................
Recommended battery types...........................................................................................
Recommended charger ...................................................................................................
Noise/vibration information
Measured values determined according to EN 62841.
Typically, the A-weighted noise levels of the tool are:
Sound pressure level (Uncertainty K=5dB(A)) ................................................................
Sound power level (Uncertainty K=5dB(A)) .....................................................................
Wear ear protectors!
Total vibration values (vector sum in the three axes) determined according to EN
62841.
Cutting particle boards *1
Vibration emission value a
.......................................................................................
h,B
Uncertainty K= .............................................................................................................
Cutting wooden beam *1
Vibration emission value a
.....................................................................................
h,WB
Uncertainty K= .............................................................................................................
*1 with saw blade bimetal, dimension 200 x 19 x 1,25 mm and tooth pitch 2,5 - 4,3 mm, 6-10 Tpi
WARNING
The vibration and noise emission level given in this information sheet has been measured in accordance with a standardized test given in EN 62841 and may be used to
compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration and noise emission level represents the main applications of the tool. However if the tool is used for diff erent applications, with diff erent
accessories or poorly maintained, the vibration and noise emission may diff er. This may signifi cantly increase the exposure level over the total working period.
An estimation of the level of exposure to vibration and noise should also take into account the times when the tool is switched off or when it is running but not actually
doing the job. This may signifi cantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the eff ects of vibration and/or noise such as: maintain the tool and the accessories, keep the hands
warm, organization of work patterns.
WARNING Read all safety warnings, instructions, illustrations and
specifi cations provided with this power tool. Failure to follow all instructions
listed below may result in electric shock, fi re and/or serious injury.
Save all warnings and instructions for future reference.
SABRE SAW SAFETY WARNINGS
Hold the power tool by insulated gripping surfaces, when performing an
operation where the cutting accessory may contact hidden wiring. Cutting
accessory contacting a „live" wire may make exposed metal parts of the power
tool „live" and could give the operator an electric shock.
Use clamps or another practical way to secure and support the workpiece
to a stable platform. Holding the workpiece by your hand or against the body
leaves it unstable and may lead to loss of control
ADDITIONAL SAFETY AND WORKING INSTRUCTIONS
Use protective equipment. Always wear safety glasses when working with the
machine. The use of protective clothing is recommended, such as dust mask,
protective gloves, sturdy non-slip footwear, helmet and ear defenders.
The dust produced when using this tool may be harmful to health. Do not inhale
the dust. Wear a suitable dust protection mask.
Do not machine any materials that present a danger to health (e.g. asbestos).
Switch the device off immediately if the insertion tool stalls! Do not switch the
device on again while the insertion tool is stalled, as doing so could trigger a
sudden recoil with a high reactive force. Determine why the insertion tool stalled
and rectify this, paying heed to the safety instructions.
The possible causes may be:
• it is tilted in the workpiece to be machined
• it has pierced through the material to be machined
• the power tool is overloaded
Do not reach into the machine while it is running.
18
ENGLISH
470 331 - BUS18CBL.indd 18
470 331 - BUS18CBL.indd 18
CORDLESS RECIPROCATING SAW
BUS18CBL
................................4749 82 01...
...000001-999999
..................................... 18 V
.............................. 0-3000 min
-1
..................................... 19 mm
................................... 255 mm
..................................... 20 mm
..................................... 20 mm
.................................... 2,1 kg
...................... 2,55 ... 3,25 kg
...........................-18...+50 °C
......................... L1820R - L1890RHD
..... BLK1218, BL1418, BL1218, AL1218G, AL18G
.................................. 84,5 dB (A)
.................................. 95,5 dB (A)
.................................. 15,4 m/s
2
.................................... 1,5 m/s
2
.................................. 15,7 m/s
2
.................................... 1,5 m/s
2
The insertion tool may become hot during use.
WARNING! Danger of burns
• when changing tools
• when setting the device down
Chips and splinters must not be removed while the machine is running.
When working in walls ceiling, or fl oor, take care to avoid electric cables and gas
or waterpipes.
Clamp your workpiece with a clamping device. Unclamped workpieces can
cause severe injury and damage.
Do not use cracked or distorted saw blades.
Plunge cuts without pre-drilling a hole are possible with soft materials (wood,
light building materials for walls). Harder materials (metals) must fi rst be drilled
with a hole corresponding to the size of the saw blade.
Remove the battery pack before starting any work on the machine.
Do not dispose of used battery packs in the household refuse or by burning
them. AEG Distributors off er to retrieve old batteries to protect our environment.
Do not store the battery pack together with metal objects (short circuit risk).
No metal parts must be allowed to enter the battery section of the charger (short
circuit risk).
Use only System GBS chargers for charging System GBS battery packs. Do not
use battery packs from other systems.
Never break open battery packs and chargers and store only in dry rooms. Keep
dry at all times.
Battery acid may leak from damaged batteries under extreme load or extreme
temperatures. In case of contact with battery acid wash it off immediately with
soap and water. In case of eye contact rinse thoroughly for at least 10 minutes
and immediately seek medical attention.
Warning! To reduce the risk of fi re, personal injury, and product damage due to
a short circuit, never immerse your tool, battery pack or charger in fl uid or allow
a fl uid to fl ow inside them. Corrosive or conductive fl uids, such as seawater,
06.11.2019 10:24:26
06.11.2019 10:24:26

Werbung

Inhaltsverzeichnis
loading

Inhaltsverzeichnis