Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Cleaning the tiller
The tiller should be cleaned after use. Use a garden hose to
wash off soil and dirt. Remove any grass, etc. from the rotor
shaft. The chassis number should only be cleaned with a
damp cloth to avoid unnecessary wear. Avoid using a high-
pressure washer during cleaning.
Storage
•
If the machine is likely to be stored unused for prolonged
periods, follow the instructions below. This will ensure
longer machine lifetime.
•
Use a garden hose to wash off soil and dirt. Remove
any grass, etc. from the rotor shaft. The chassis number
should only be cleaned with a damp cloth to avoid
unnecessary wear. Avoid using a high-pressure washer
during cleaning.
•
Wipe the tiller with a damp cloth so that all surfaces are
clean. Wipe the surfaces down with an oily cloth to
prevent rust.
•
Always store the machine in a dry, clean location.
Troubleshooting
The motor will not start
1.
Check that the safety key is fitted correctly.
2.
Check that the battery is fully charged and mounted
correctly in the right side of the battery compartment.
3.
Make sure to hold the safety switch down before
activating the clutch handle.
The blades will not rotate
1.
Check for stones lodged between the blades.
2.
Release any stones by removing the blades.
3.
Check the cables are in good working order and fitted
correctly.
4.
Check the belt is in good working order and fitted
correctly.
5.
Ensure the belt tensioner is adjusted correctly.
Control panel flashes green (when hold clutch handle)
1.
The battery is discharged. Set it to charge
2.
The controller or battery is hot. Let it cool down.
3.
Connection failed. Reinstall battery and restart.
Control panel flashes orange (when hold clutch handle)
1.
The blades or gearbox may be blocked.
Release any stones by removing the blades.
2.
Start failed. Switch off the machine and start again.
Noise, vibration and precautionary measures
1.
Long-term exposure to noise levels exceeding 85 dB (A)
are damaging. Always use ear defenders when the
machine is being used.
2.
To reduce noise levels further, only use the machine in
an open environment.
3.
Vibrations can be reduced further by holding the handle
firmly.
4.
To avoid disturbing others, the machine should only be
used during the daytime.
5.
Always wear close-fitting work clothes, hard-wearing
work gloves, ear defenders and non-slip boots with steel
toecaps.
6.
Take 30-minute break every 2 working hours.
7.
A worn belt must be replaced/ serviced by an authorized
dealer
Warranty terms and conditions
The warranty period is 2 years for private end users in EU
countries.
Products sold for commercial use, only have a warranty
period of 1 year.
The warranty covers material and/or fabrication faults.
Restrictions and requirements
Normal wear and replacement of wearing parts are NOT
covered by the warranty.
Wearing parts, which are NOT covered for more than 12
months:
•
Blades
•
Cables
•
Belts
•
Switches
•
Battery: If the battery is not stored correct (frost-free and
recharged every 3 months), the durability is only
guaranteed for 6 months
The warranty does NOT cover damages/faults caused
by:
•
Lack of service and maintenance
•
Structural changes
•
Exposure to unusual external conditions
•
Damages to the bodywork, deck, handles, panels etc.
•
If the machine has been improperly used or overloaded
•
Use of unoriginal spare parts.
•
Other conditions where Texas cannot be held
responsible.
Whether a case is a warranty claim or not is determined in
each case by an authorized service center.
Your receipt is your warranty note, why it should always be
kept safe.
REMEMBER: The purchase of spare parts as well as any
request for warranty repair, art. no. (e.g. 900XXXXX), year
and serial number should always be informed. It can be
found on the CE-label on the machine!
* We reserve the right to change the conditions and accept
no liability for any misprints
14
Werbung
Inhaltsverzeichnis
