Texas CTX2000 Bedienungsanleitung Seite 12

Cleaning the tiller
The tiller should be cleaned after use. Use a garden hose to
wash off soil and dirt. Remove any grass, etc. from the rotor
shaft. The chassis number should only be cleaned with a
damp cloth to avoid unnecessary wear. Avoid using a high-
pressure washer during cleaning.
Storage
•
If the machine is likely to be stored unused for prolonged
periods, follow the instructions below. This will ensure
longer machine lifetime.
•
Use a garden hose to wash off soil and dirt. Remove
any grass, etc. from the rotor shaft. The chassis number
should only be cleaned with a damp cloth to avoid
unnecessary wear. Avoid using a high-pressure washer
during cleaning.
•
Wipe the tiller with a damp cloth so that all surfaces are
clean. Wipe the surfaces down with an oily cloth to
prevent rust.
•
Always store the machine in a dry, clean location.
Troubleshooting
The motor will not start
1. Check that the batteries are fitted in correctly.
2. Check that the safety key is fitted correctly.
3. Make sure to hold the safety switch down before
activating the clutch handle.
The blades will not rotate
1. Check for stones lodged between the blades.
2. Release any stones by removing the blades.
3. Check the cables are in good working order and fitted
correctly.
Noise, vibration and precautionary measures
1. Long-term exposure to noise levels exceeding 85 dB (A)
are damaging. Always use ear defenders when the
machine is being used.
2. To reduce noise levels further, only use the machine in
an open environment.
3. Vibrations can be reduced further by holding the handle
firmly.
4. To avoid disturbing others, the machine should only be
used during the daytime.
5. Always wear close-fitting work clothes, hard-wearing
work gloves, ear defenders and non-slip boots with steel
toecaps.
6. Take 30-minute break every 2 working hours.
7. A worn belt must be replaced/ serviced by an authorized
dealer
Battery
This product is delivered without battery and charger. It
is sold separately.
To get the best performance of this machine, it is
recommended to use 2 x 4.0Ah battery.
Warning: Do not try to disassemble, short circuit or put it to
extreme heat or fire, as it can cause serious inquiry and
permanent damage to the battery!
Battery pack is not fully charged when delivered.
Charging
•
Only use the original charger with
art. no. 90063242
•
Before the battery is being used the first time, it is
recommended to fully charge it first.
LED lights
All LEDs are lit
LED 1, LED 2, LED 3
are lit.
LED 1, LED 2
are lit.
LED 1 are lit
LED 1 flashes
Note: The indicator lighs is only indicative indications and is
not accurate power indications.
Important: To protect the battery from total discharge, the
machine will stop, when the battery is nearly empty.
The machine must not be started up again after automatic
shutdown, as it can damage the battery.
The battery must be recharges before the work can continue.
Charging
A full charge takes around 60 min for 2.0 Ah batteri and
120 min for 4.0 Ah battery.
•
Only use the original charger*
•
Do not try to charge other type of batteries in the
charger, other than the original batteries with art. no.
90063245 (2.0 Ah) or 90063246 (4.0 Ah).
•
Keep the charger in a dry and warm environment (10-
25 degrees C) and only use it indoor. It should be
connected to a normal 230V AC socket.
•
Before the battery is being used the first time, it is
recommended to charge it fully.
•
The surface of the battery can become warm during
charging. This is normal.
•
Do not cover battery or charger during charging. Allow
free ventilation of air.
Insert the battery into the slots of the charger and slide it
into place until it locks.
There are 4 lights on the charger indicating the status and
state of charge of the battery
12
Battery Pack
Fully charged (75-
100%).
The battery pack is
50%-75% charged
The battery pack is
25%-50% charged.
The battery pack is
0%-25% charged
The battery pack is
empty. Charge the
battery.
Status
Charging
Fully charged
Evaluate
Defective