Led Lenser H7.2 Bedienungsanleitung Seite 3

English | Page 02-04
We are delighted that you have purchased one
of our products.
These are usage instructions to help you
familiarize yourself with your new purchase.
All the documents accompanying the product
must be read attentively before using the
product, stored for future use and if the product
is transferred to a third party, the documents
should be handed over as well. This ensures
that maximum benefit is drawn from the product
and questions from users can be resolved when
they arise.
Above all, comply with the warnings and safety
instructions and dispose of the packaging
material properly.
Additional information for H7.2 with "TEST IT"
function
Your LED LENSER H7.2 headlamp is packaged
with a "TEST IT" function (item no. 7397). This
allows users to test the brightness while the
product is still in the package. For testing,
simply push the yellow "TEST IT" button on the
front of the package. When testing, please do
not look directly into the light.
The "TEST IT" button is connected to the battery
housing of the H7.2 via two wires and should be
removed prior to use.
To remove the "TEST IT" button and wires,
open the battery box and remove the 4 x AAA
batteries (see also "Changing Alkaline Batteries"
further below). Separate the two "TEST IT"
button wires from the battery housing by pulling
on each wire until it releases from the battery
housing. Insert the 1xLi-ion battery pack or 4
x AAA battery and noting the correct polarity.
Close the battery box. Please dispose and
recycle the packaging and "TEST IT" button with
the wires according to the local regulations.
Product
7297, LED LENSER® H7.2 (gift box)
7397, LED LENSER® H7.2 (Blister with "TEST IT"
function)
Version of the operating manual: V 1.3
1.Battery set:
4 x AAA / LR03 (1.5 V DC)
2. Turning it ON and OFF
There are two switches on the H7.2. The front
switch is located in the upper part of the
headlamp housing. This button is used to turn
the H7.2 ON/OFF. It is also used to activate the
various Light Programs, Lighting Functions (see
Section 5.1) and to active the "transport lock"
function (see Section 6).
The Multi-function "Wheel" switch is located
on the backside in the upper part of the battery
box. This allows you to adjust the brightness
and flash rate infinitely and to change the light
modes (see Section 5.1).
3. Focus
In the front, narrower region of the headlamp
housing is the reflector lens through which
the light of the LED is focusable. The reflector
lens is held by a plastic ring. You can rotate
that plastic ring using two fingers, and thus
adjust the focus quickly and easily. This is our
patented Speed Focus system, which allows the
adjustment of the light beam's focus.
You also can adjust the hinge of the headlamp,
depending on whether you want to illuminate
an area in the distance or in front of you. For
this, you simply tilt the part of the head lamp
containing the reflector lens and the LED.
4. Smart Light Technology (SLT)
Smart Light Technology (SLT) is a program that
consists of computer optimized microcontrollers
which allows our products to have various
lighting functions. The H7.2 is equipped with
this technology and is therefore able to use
various Light Programs and Functions (see
Section 5) with an interface that is simple and
user friendly. By pressing the front switch on
the lamp head you can activate the following
light functions: On (Power) – Off, Low Power,
Boost and Signal. With the Multi-function "Wheel"
switch on the back, the light intensity (down
to 5 lm) and flashing rate (1–24Hz) is infinitely
adjustable by easily rotating the switch. By
pressing the "Multi-function Wheel" switch you
can change the light mode.
5. Light Programs and Light Functions
The H7.2 is equipped with one LED (Light
Emitting Diode). The LED is very strong and
ideal for normal use. For example if the Turning
Focus or the adjustment of the angle of light
beam to the horizontal should be used.
The boost mode of H7.2 can be turned on when
the flashlight is off and then pushing the front
switch for approx. 5 seconds. Release the switch
when the boosted light is on, otherwise the
product will enter "transport lock" (see Section
6).
5.1 Light Programs
In H7.2, there are three different modes (Easy
Low, Easy Power, Signal). The default mode is
the Easy Low mode.
When the product is off, press the "Multi-function
Wheel" switch on the back for 5 second. It will
achieve transition mode. Then the LED will blink
once to indicate that it is mode one; then blink
twice for mode two; and finally blink thrice for
mode three.
a) Light Mode one - Easy Low: when the product
is off, firmly press the front button until it blinks
once. The LED will glow at its lowest brightness
(light function: dim light). Two times touch to
the button on top of the lamp within 1 second
will turn on the lamp to its full brightness (light
function: strong light), and third touch will turn
the lamp off.
b) Light Mode two - Easy Power: when the
product is off, firmly press the front button until
it blinks twice. The LED will glow at its fullest
brightness (light function: strong light). Two
times touch to the button on top of the lamp
within 1 second will turn on the lamp to its
lowest brightness (light function: dim), and third
touch will turn the lamp off.
c) Light Mode three - Signal: when the product
is off, firmly press the front button until it blinks
thrice. The LED will glows with full brightness
(light function: strong light). Two times touch to
the button on top of the lamp within 1 second
will start the strobe (12 Hz), and a third touch
will turn the lamp off. The speed at which the
strobe will blink can be adjusted by turning the
knob on the battery box.
When the flashlight is on, rotate the "Multi-
function Wheel" switch on the back to adjust the
GB
02